New products

Product Information »  New Products List

New Products List

Non F-Gas (CO2 Refrigerant) Refrigerated Thermo-chiller HRZC Series

New

Updated Sep-24

  • Non F-Gas
  • Uses a CO2 refrigerant
  • Greatly reduced GWP
  • GWP = 1 Compliant with each country’s refrigerant regulations
    As of the end of September 2024
    EU refrigerant regulations: GWP150 or more
    US refrigerant regulations: GWP700 or more
    California, US refrigerant regulations: GWP750 or more
    ∗ “GWP” indicates the global warming potential. The values are based on the IPCC AR4.
  • Air transport possible
  • Eliminates the need to pay for F-Gas recovery & disposal
  • Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Low GWP Refrigerant Chiller Thermo-chiller Standard Type HRSF150/200 Series

New

Updated Sep-24

  • Low GWP Refrigerant Chiller
    GWP: 146 ∗Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
    EU refrigerant regulations: GWP150 or more
    US refrigerant regulations: GWP700 or more
    California, US refrigerant regulations: GWP750 or more
  • Environmentally friendly R454C as refrigerant (Not available for air transport)
  • No heater is required, as the circulating fluid is heated using only the heat exhausted by the refrigerating circuit.
  • Compatible with power supplies in Europe, Asia, Oceania, and North, Central, and South America
    3-phase 400 VAC
  • Low-noise design 70 dB(A)
  • Outdoor installation IPX4

[Model with Residual Pressure Release Function] Compact Indicator Type Speed Controller with Pilot Check Valve ASP-S Series

New

Updated Sep-24

  • Flow rate control is possible via the compact indicator.
  • Model with residual pressure release function: Cylinder pressure can be manually released.
  • Model without residual pressure release function: Temporary intermediate stops are possible.
  • Horizontal and vertical types are available, which can be selected depending on the installation conditions.
  • Easily mounted using a hexagon wrench

3-Screen Display Condensation Checker (Digital Temperature & Humidity Switch) PSH Series

New

Updated Sep-24

  • A relative humidity under pressure (inside piping) display function has been added. [New]
  • A condensation checker can prevent such problems!
    Allows for the visualization of humidity inside piping
    Detects abnormalities prior to condensation generation
  • Can be easily connected to any pipe you want to monitor
    Compact size allows for easy installation
  • Visualization of relative humidity
    Real-time monitoring
  • Remote/Condition monitoring
    Remote confirmation via switch output preventing condensation problems!

ISO 13849-1 Compliant Safe Exhaust Valve Modular Connection Type VPX400 Series

New

Updated Sep-24

  • Safety standard ISO 13849-1 compliant
    (Corresponding to categories 3 and 4)
  • Exhaust flow rate characteristics [L/min (ANR)] ∗ At 0.6 MPa
    10,500 (VPX406-A3)
    13,000 (VPX406-A3)
    15,000 (VPX406-A6)
  • Space saving & lightweight: 3 functions have been integrated.
    Dual residual pressure release valve + Soft start-up valve + Main valve inconsistency detection
  • Modular connection is possible.
    (AC30/40/50/60-D series)

Suction Cup/Compatible with Metal Detectors HF3A-ZP3F Series

New

Updated Sep-24

  • Bellows type cup with excellent cushioning and flexibility
    Reduces the deformation of soft workpieces such as bread
  • The cups and retainers are made of materials compliant with the FDA (U.S. Food and Drug Administration)
    dissolution test, EC directives, and Japan Food Sanitation Act standards.
  • Improved durability due to anti-stick grooves
  • Equipment for the food manufacturing industry HF3A- series

Pilot Operated 2-Port Solenoid Valve JSXH-X1

New

Updated Sep-24

  • Max. operating pressure differential: 4.0 MPa
    Application examples: Blow molding, Laser processing machines, Nitrogen filling unit
  • Fluid: Compressed air, Nitrogen, Argon, Oxygen
    ∗ When using oxygen, please refer to "Fluid Supply."
  • Improved environmental resistance
    Dustproof/waterproof IP67 structure (IP65 for the DIN terminal)
    With a stainless steel coil cover
  • Low particle generation
  • Oil-free
  • Easy maintenance
    The coil can be replaced by simply removing the clip.
  • Power saving (Power consumption: 6 W)

Compact Guide Cylinder ø12, ø16, ø20, ø25, ø32, ø40, ø50 MGPK Series

New

Updated Aug-24

  • A type with an air cushion has been added for
    bore sizes ø12 to ø50. [New]
  • Volume: Max. 28% reduction(538cm3 → 390cm3
  • Weight: Max. 41% reduction (0.32 kg → 0.19 kg)
  • High rigidity: Optimized configuration allows for compact body with high rigidity
    Plate thickness increased by up to 33%, Higher rigidity
  • Lube-retainer is added to the guide rod.

Standard Air Cylinder (Square Cover) MB2/MDB2 Series

New

Updated Aug-24

  • 3 times better durability due to the air cushion + rubber bumper structure
  • Allowable kinetic energy: Max. 1.5 times
    Has the same kinetic energy as the existing MB series product which is 1 size larger
  • CO2 emissions (Air consumption) can be reduced by up to 39%.
    CO2 emissions (Air consumption) can be reduced due to downsizing. (Air consumption for one cycle)
  • The overall length, mounting dimensions, and mounting brackets are interchangeable with the existing MB series product.

Compact 5-Port Solenoid Valve A top-ported type JSY3000 Series

New

Updated Jul-24

  • A top-ported type has been added to the JSY3000 series.
  • 4(A) and 2(B) port output pressure detection is possible.
    (Caution) The mounting bases are side ported.

Longer Life Cylinder C55-XB24

New

Updated Jul-24

  • New technology offers at least 4 times better durability.
  • The maintenance intervals will be extended.
  • Employs the same specifications and dimensions as the existing model,
    C55 ISO Cylinder series.
  • ISO Standards (21287)

Energy Saving, Exhaust-Recovery Booster Regulator VBAE Series

New

Updated Jul-24

  • CO2 emissions (Air consumption) :Max. 40% reduction
    (Based on SMC's measuring conditions)
    Driven by reusing the exhaust air
  • Increase factory air pressure by 1.7 times Air-only operation that requires no power supply, and allows for easy installation.
  • Operation noise: 65 dB (A)
    15 dB (A) reduction compared with the existing model (VBA series) (Based on SMC's measuring conditions)
  • Charging time: Max. 50% shorter
    Reduced maintenance frequency due to improved life
    (Based on SMC's measuring conditions)
  • Compatible with vertical and horizontal installation
  • Mounting interchangeability with the existing model (VBA series)

2-Color Display
Digital Flow Switch PF2M7(-L) Series

New

Updated Jul-24

  • 3-Screen Display Digital Flow Monitor (Dedicated for the PF2M7) [New]
    Allows for the monitoring of remote lines PFGM302 Series
  • Dry air, N2, Ar, CO2
  • A wide range of flow measurement is possible with 1 product.
    Flow ratio 100:1, Smallest settable increment: 0.01 L/min
  • Improved resistance to moisture and foreign matter
  • Compact, Lightweight
    Weight: 27.3% lighter (55g ⇒ 40g)
  • Low current consumption: 35 mA or less
  • Grease-free
  • IO-Link compatible

Biomass Tubing TU/TS/T-X309

New

Updated Jul-24

  • Tubing according to carbon neutrality
  • CO2 reduction amount: Max. 18.7 kg
    ∗ Comparison with the TS series (Tubing O.D. 12 mm; Tubing I.D. 9 mm), Soft nylon tubing, 100 meters roll
  • Reduction in CO2 and greenhouse gases by reducing the use of petroleum driven raw materials, resulting in a greater contribution towards decarbonization.

  • What is a biomass tube?
    Tubing produced from plant derived raw iomaterials such as castor seeds, etc.

High Purity Air Operated Chemical Liquid Valve JLV20/30/40/50 Series

New

Updated Jun-24

  • Body class 4 has been added.[New]
  • Suppresses the generation of particles and reduced footprint!
    The special structure allows for reduced impact when the valve is closed
    as well as particle generation suppression.
    Reduced footprint (Compared to the existing model):
    Valve width reduced by 20%, Mounting pitch reduced by 45%
  • Applicable for applications requiring high pressure/high back pressure
    Operating pressure: 0 to 0.5 MPa, Back pressure: 0 to 0.5 MPa
     (Improved by 66% compared to the existing model)

Vacuum Gripper System (Foam Type) ZGS Series

New

Updated Jun-24

  • Compatible with the collaborative robots of 4 companies
    UNIVERSAL ROBOTS OMRON/TECHMAN ROBOT,FANUC, YASKAWA Electric [New]
  • Suitable for the palletizing and depalletizing of corrugated cardboard, etc.
  • Combines all functions required for adsorption
    Ejector unit
    (Ejector, Supply valve/Release valve, Silencer, Pressure switch)
  • Can be used immediately by simply connecting 1 electrical cable and air piping
  • Weight: 3.9kg Reduces the load on robots
    * For ZGSNPK-400240BS4-RM1C8
  • CO2 emissions (Air consumption) (SMC comparison)
    Ejector with new design
    227 L/min (ANR) ← 270 L/min (ANR)
    Compared to ZL6H (Supply pressure: 0.6 MPa)

Electric Stopper Cylinder LEB□ Series

New

Updated Jun-24

  • Designed in response to customers' requests for a motorized conveyor line
  • With 2 control types available depending on the application
    Controller
    Controllerless
  • Ensured stopper cylinder mounting interchangeability with equivalent stopper performance
  • Easy replacement of shock absorbers Replaceable just by loosening the set screw

ISO Standards (21287) Compact Cylinder C55/CD55 Series

New

Updated Jun-24

  • ISO Standards (21287)
  • 1.8 times the anti-lateral load capacity [New]
    The allowable lateral load has been improved by changing the material of the bushing. (For ø20)
  • Increased the standard product's maximum stroke limit (to 300 mm) [New]
  • Standardization of the Double rod (C55W) type, Simple specials, and Made-to-order options [New]
    Change of rod end shape (-XA□)
    Heat-resistant cylinder (–10°C to 150°C) (-XB6)
    Low-speed cylinder (5 to 50 mm/s) (-XB13)

Electric Actuator/Rod Type Dust-tight/Water-jet-proof (IP69K Equivalent)  HF2A-LEY Series

New

Updated Jun-24

  • Enclosure: IP69K equivalent
    Smooth design for less residual liquid accumulation
    External parts: Stainless steel 304
    Scraper, Static seal: US FDA compliant material (Blue), EC1935/2004 compliant material
    Grease: NSF-H1 grade
  • Equipment for the Food Manufacturing Industry HF2A- Series
  • Lubricants or rust proof agents are not used for the external parts.
    Otherwise, lubricants or rust proof agents for the food machinery are being used.
  • US FDA compliant materials are used.
  • Work load: Max. 80 kg  ∗ Size 63, Lead C
  • Stroke:Max. 800 mm  ∗ Size 63

    IP69K is the degree of protection against dust and hightemperature/high-pressure water washdown specified in DIN 40050-9 and currently specified in ISO 20653 and JIS D 5020.

Separate Controller Ionizer / Slim Bar Type IZT44/45 Series

New

Updated Jun-24

  • Powerfully eliminates static electricity from highly charged workpieces
    Pulse AC type, High density emitter arrangement (6 times the number of emitters)
    ∗ Compared to the existing model
  • Can be mounted in a narrow space (Height 23 mm x Width 20 mm)
    Can be installed through gaps between equipment
    Improved installation, replacement, and maintenance in narrow spaces
  • Powerful static elimination is possible without air supply.
  • High speed static elimination: Discharge time reduced by approx. 60%
  • 2-way directional static elimination using branch cables
    2 ionizer bars can be connected to one high voltage power supply.
  • Up to 4 high voltage power supply modules can be connected to one controller. (IZT45)
  • Flexible layout possible with various module connection methods (IZT45)
    Controller to Bar maximum installation distance: 15 m

Electro-pneumatic Regulator Integrated Type 64-station Compatible Manifold Plug-in Compact 5-Port Solenoid Valve JSY3000-P Series

New

Updated Jun-24

  • Solenoid valves and electro-pneumatic regulators can be connected to the same manifold.
    Valve stations/Number of outputs: For 4 to 64 stations /128 points
    ∗ Stations are only available in multiples of 4.
    Electro-pneumatic regulator stations: 1 to 4 stations
    I/O unit stations: Max. 8 stations
  • Equipment integration allows for the centralized management of control and wiring as well as reduced wiring
    Reduced wiring, Reduced number of SI units, Reduced wiring work, Compact

64-station Compatible Manifold Plug-in Compact 5-Port Solenoid Valve JSY3000-L Series

New

Updated Jun-24

  • Valve stations/Number of outputs: For 4 to 64 stations /128 points
    ∗ Stations are only available in multiples of 4.
  • Space saving, Reduced number of SI units, Reduced wiring and wiring work

Speed Controller with Compact Indicator AS-FSA Series

Updated May-24

  • Height: Max. 5.4 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • A type with a panel mount adapter has been added. [New]
    No tools required, Reduced installation work

In-line Type AS Series

Updated May-24

  • A panel mount type has been added. [New]
    No tools required, Reduced installation work
  • Reduces labor time
    Easy to use push-lock type
    Knob O.D.: Almost doubled
  • Improved reproducibility of flow rate
  • Lightweight: Weight reduced by approx. 27%
  • Electroless nickel plated type is standard.

Electric Actuator/Slider Type (Improved Dust and Water-jet Resistance) LEFSW Series

Updated May-24

  • A dust-tight and water-jet-resistant (IP65 equivalent) slider type product
    Newly developed special wear-resistant seal band
    A special wear-resistant seal band is mounted on the bottom to prevent dust and water from entering the inside of the product.
  • With internal battery-less absolute encoder
    Restart from the last stop position is possible after recovery of the power supply.
    Reduced maintenance (No need to manage or replace batteries)
  • Work load:Max. 65 kg (Size 40, Lead B)
  • Stroke:Max. 1200 mm (Size 40)

Low GWP Refrigerant Chiller/Refrigerated Thermo-chiller HRZF Series

Updated May-24

  • Low GWP refrigerant chiller
    GWP: 146 ∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
    EU refrigerant regulations: GWP150 or more
    US refrigerant regulations: GWP700 or more
    California, US refrigerant regulations: GWP750 or more
  • Environmentally friendly R454C as refrigerant (Not available for air transport)
  • More effective energy-saving is achieved through use of a DC inverter compressor and an inverter pump.

Compact Slide ø6, ø10, ø16, ø20, ø25 MXH2 Series

Updated Apr-24

  • Size ø25 have been added. [New]
  • Same width as size ø20
    Allowable moment: Max. 1.4 times greater than that of size ø20
  • Improved linear guide rigidity reduces the amount of table displacement by 48%
    Displacement due to a force acting in the pitch direction: 48% reduction (0.31 mm→0.16 mm)
    Displacement due to a force acting in the yaw direction: 63% reduction (0.24 mm→0.09 mm)
    Displacement due to a force acting in the roll direction: 90% reduction (0.06 mm→0.006 mm)
  • Max. standard stroke: 150 mm (For ø20, ø25)[New]
  • Weight: Max. 6% reduction (194 g→182 g)
  • Dimensions for mounting and length are equivalent to the existing MXH series.

Stainless Steel Speed Controller (Max. operating temperature: 150°C) In-line Type ASG Series

Updated Apr-24

  • Improved corrosion/heat resistance with the all stainless steel exterior
    Possible for use in environments such as high temperature, water splashing, and where copper and zinc cannot be used
  • Material: Stainless steel 316 (External metal parts), FKM (Seal)
    ∗ Stainless steel 304 is used as the material for parts other than body A.
  • Max. operating temperature: 150°C
  • NSF H1 grease

Pulse Blow Valve AXTS040-X202

Updated Apr-24

  • The peak pressure of repeatedly colliding air permits efficient blowing.
  • CO2 emissions (Air consumption) : 50% reduction
  • Control for pulse generation is not required.
    Pulse blow can be used by simply supplying air.
  • Built-in pilot valve construction allows for stable blowing.

Air Management System AMS20/30/40/60 Series

Updated Apr-24

  • Air consumption: Max. 62% reduction
    Monitors the machine standby conditions (when production stops) and automatically decreases the pressure.
    Reduces unnecessary air consumption
  • Compatible with OPC UA
    Direct connection enables data communications.
  • Compatible with wireless systems
    Communication cables not required
    High security thanks to unique encryption
    Communication distance: Max. 100 m
  • IO-Link compatible

Low-Pressure / High-Precision Type 5.0 MPa Maximum Supply Pressure High Pressure Electro-Pneumatic Regulator ITVX2030-X10

Updated Mar-24

  • Improved accuracy at 1 MPa or less
    Repeatability: Repeatability
    Pressure stability: 0.5% F.S. or less
  • Max. supply pressure: 5.0 MPa
  • Set pressure range: 0.01 to 3.0 MPa
  • Max. flow rate: 3000 L/min (ANR)
  • Fluid: Air, N2, O2, Ar
  • Wetted parts: Fluorine grease

Compact Cylinder/High Power Type CQE Series

Updated Mar-24

  • Sizes 25 and 40 have been added. [New]
  • Theoretical output: 1.5 times
  • This is done even with the same external dimensions of the CQ2 series.
  • The theoretical output of the next larger bore sized cylinder is made possible with the polygonal piston shape.
  • Contributes to a lower pressure air line
    Supply pressure decreaed by 0.17 MPa
    The same theoretical output is available even when the supply pressure to the cylinder is decreased.

Compact Cylinder  CQ2/CDQ2 Series

Updated Mar-24

  • Sizes ø4, ø6, and ø10 have been added. [New]
  • ø4 to ø200 lineup
  • Space-saving cylinder designed with a compact body
  • Small auto switches can be mounted on 4 surfaces. (1 surface for ø6 annd ø10, 2 surfaces for ø12 to ø25)
  • No projection of the auto switch
  • Weight: Reduced by 5 to 13% (Compared with the existing CQ2 series)
  • Newly added compact type foot brackets and double clevis pivot bracket
  • Part numbers with a rod end bracket and/or mounting bolt are available. (It is not necessary to order a bracket for the applicable cylinder separately.)
  • With auto switch (CDQ2 series: CDQ2, CDQ2W, CDQ2K, CDQ2KW, CDQP2, CDQ2□S, CDBQ2)

[Compatible with Manifold Controller] Electric Actuators Slider Type/Rod Type LE2FS□H/LE2Y□H Series

Updated Mar-24

  • Compatible with manifold controller
    Up to 16 axes can be connected
  • Annual CO2 emissions reduced by up to 38% through motor control optimization (SMC comparison)
    8.7 kg-CO2e/year (14.1)
    ∗ The numerical values vary depending on the operating conditions.
  • Battery-less absolute encoder type
    Restart from the last stop position is possible.

Manifold Controller JXD1-M□ Series

Updated Mar-24

  • Up to 16 axes can be connected
    Max. 8 driver units can be connected
  • Fanless design (no cooling fan)
    No cooling fan = No need to worry about fan replacement
  • Operating temperature range: 0 to 55°C
  • Communication protocol
    CC-Link
    EtherNet/IP™
    EtherCAT®
    PROFINET®
  • Cables, etc. can be attached from the front.

Direct Operated/Pilot Operated 2-Port Solenoid Valve JSX/JSX□ Series

Updated Mar-24

  • A pilot operated steam type (JSXP series) has been added. [New]
  • Improved environmental resistance due to the stainless steel coil cover【IP67 enclosure/NEMA4X
    ∗ IP65 for models with a DIN terminal
  • Space saving
    Compact: Valve volume reduced by 25%, Lightweight: Weight reduced by 30%
    ∗ Compared with the existing model
  • Energy saving
    Coil force: 10% increase, Power consumption: 14% reduction
    ∗ Compared with the existing model
  • 360° lead wire insertion and removal is possible.
  • Improved weather resistance in outdoor environments

Multi Hand Adapter RMMA Series

Updated Mar-24

  • Allows for the handling of various workpieces by a single robot
  • Allows for the simultaneous transfer of multiple workpieces
  • Up to 3 grippers can be mounted.
  • Reduces tool changing time
  • Robot arm end standards: Equivalent to ISO9409-1-50-4-M6
  • 3 gripper mounting angles

Air Flow Controller IN502-44/45/46

Updated Mar-24

  • A rated control flow rate range of 200 to 2000 L/min has been added. [New]
  • Automatic flow rate adjustment is possible.
  • Dry air, N2
  • Control accuracy: ±5% F.S.
  • Responsiveness: 0.5 s or less
  • Space saving/Reduced piping, wiring, and installation labor
  • Various types of grease can be selected.
    Grease compatible with low dew points, White vaseline, Grease for food
  • IO-Link compatible

Modular Type Water Separator AFG-D Series

Updated Mar-24

  • The no filter element design achieves a large flow and maintenance free construction.
  • Water droplets are removed by centrifugal force.(Water droplet removal ratio: 99%)
    Air containing water droplets is rotated to remove them by centrifugal force.
  • Modular Design with Uniform Body Style

2-Layer Fluoropolymer Polyurethane Tubing TUE Series

Updated Mar-24

  • 2-layer tube with excellent environmental resistance and flexibility
    Outer layer: Fluoropolymer, Inner layer: Polyurethane
  • Tubing I.D.: Cross-section ratio increased by 44% (Compared to TU0805)
  • Wide color variations
    Available in black, white, blue, and translucent colors.

Longer Life Cylinder C85/C75-XB24

Updated Mar-24

  • New technology offers at least 4 times better durability.
  • The maintenance intervals will be extended.
  • Employs the same specification and imensions as the existing models,
    C85 ISO Cylinder series and C75 Air Cylinder series.

Multistage Ejector ZL1/ZL3/ZL6 Series

Updated Mar-24

  • An IO-Link compatible vacuum pressure switch has been added. (ZL3, ZL6) [New]
    Allows for ejector control with a single communication line
    Reading of the device information and parameter batch settings are possible.
  • Max. suction flow rate: 3 types available: 100, 300, and 600 L/min (ANR)
  • Air consumption: 91% reduction (ZL3, ZL6)
    Reduced by the pressure switch for vacuum with energy saving function and efficient ejectors
  • Weight: Max. 60% reduction [ZL112 (Existing model): 450 g → ZL1: 180 g]

Remote Type Pressure Sensors/Pressure Sensor Controllers PSE Series

Updated Feb-24

  • Switch output specification [New]
  • IO-Link compatible [New]

e-Actuator Easy to Operate Integrated Controller Slider Type/Rod Type EQFS□H/EQY□H Series

Updated Feb-24

  • Size 16 has been added. [New]
  • Easy to set up, just like air equipment!
    Two position stop with no programming required
    Three position stop with no programming required
    Cycle time can be set in all control modes.
  • Downsized with Integrated Controller, Wiring saving, Labor saving
    · Programless · Reduced adjustment time
  • Annual CO2emissions reduced by up to 59% through motor control optimization [5.8 kg-CO2e/year (14.1)]
    ∗ The numerical values vary depending on the operating conditions.

Elastic Finger MH-X7654

Updated Feb-24

  • Rubber sheet fingers enable gripping of an indefinite workpiece
  • Design of the finger according to the workpiece shape is not required.
  • Allows for gripping of tightly packed workpieces
    The elastic finger mounting attachment to be produced by the customer.
  • Material
     ・Silicone rubber (Blue)
      This product is made of materials compliant with FDA
       (U.S. Food and Drug Administration) regulations
      as well as Japan Food Sanitation Act standards.
     ・EPDM (Black)

Wireless System EXW1/EX600-W Series

Updated Feb-24

  • DeviceNet®has been added to the compact type EXW1 Series [New]
  • Noise resistance
     Uses the 2.4 GHz ISM frequency band
     Frequency hopping: Every 2 ms (Fastest)
  • Communication cables not required
    Reduced wiring work, space, and cost
    Minimized disconnection risk
  • Provides communication stability in FA environments
  • Compact and lightweight (EXW1)
    Volume: Approx. 81% reduction, Weight: Approx. 79% reduction
  • Modular connection is possible. (EX600-W)

Electric Vacuum Gripper for Collaborative Robots ZXPE5 Series

Updated Feb-24

  • Can be used with the collaborative robots of 4 companies
    UNIVERSAL ROBOTS
    OMRON/TECHMAN ROBOT [New]
    FANUC CORPORATION [New]
    ASKAWA Electric Corporation [New]
  • A vacuum gripper that doesn't require an air source
  • Operation possible by simply connecting an electrical wire connector
    Can be used without an air source due to the built-in vacuum pump
  • Unitization of the peripheral devices required for adsorption
    The vacuum pump, atmospheric release valve, pressure monitor, and cups have been integrated.
  • Current consumption: Max. 64% reduction
    Energy-saving operation possible via automatic/manual modes
  • Lightweight: 556 g
  • A wide variety of cup variations are available to support a wide range of workpiece shapes.
  • Standards: Conforming to ISO9409-1-50-4-M6

Thermo-chillers for the Semiconductor Industry INR-495-042/INR-495-043

Updated Feb-24

  • Non F-Gas (CO2 refrigerant)
  • GWP: 1 (Natural refrigerant)
  • EU refrigerant regulations: GWP150 or less
  • US refrigerant regulations: GWP700 or less
  • California, US refrigerant regulations: GWP750 or less
    ∗As of December 2023
  • Air transport possible
    No air transport restrictions for non-toxic and non-flammable refrigerants
    ∗A1 (ASHRAE34 standard)
  • No F-Gas management required
    Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)
  • No F-Gas recovery & disposal costs

Metal Speed Controller/Low Profile Type ASBL Series

Updated Feb-24

  • Improved environmental resistance with the all metal exterior
  • For use in environments with welding spatter, dust, ultraviolet, etc.
  • Improved installability using a hexagon wrench
  • Improved piping design flexibility (360° rotation)
  • Reduced height when installed: Approx. 30% reduction
    (when a knob is fully opened)
    ∗ 21.2 mm: ASBL23□1-01-06 ◀ 30.9 mm: ASB22□1-01-06

Motorless Type LE□ Series

Updated Feb-24

  • A large slider type (LET-X11 series) has been added. [New]
  • A high precision type slide table (LESYH series) has been added. [New]
  • Your motor and driver can be used together
  • Manufacturers of compatible motors: 18 companies

Analog Auto Switch and Display Sensor Monitor D-MH1□ Series

Updated Feb-24

  • Outputs the analog voltage according to the actuator stroke position
  • A single switch can discriminate between max. 3 position points.
    Discriminable resolution: ±0.1 mm ∗ Within the high-resolution range
  • Detection position setting can be done away from the actuator.
  • Analog voltage output (1 to 5 V)
     Can also be used with the analog auto switch single unit
  • Reduced setting labor
     No need to fine-tune the switch mounting position
     Easy adjustment even in narrow places and on moving parts
  • Improved productivity
     Gripper fully open R gripping R gripping failure detection
     Detection of gripper finger wear
     Minimized lead wire disconnection risk

Vacuum Unit Ejector System/Vacuum Pump System ZK2□A Series

Updated Jan-24

  • Supply valve: An N.O. specification has been added. [New]
    Can hold vacuum even when the power goes out or is turned off
    Prevents the sudden dropping of workpieces
    ∗ Supposing the supply pressure is being maintained
  • An IO-Link compatible pressure switch has been added. [New]
    Allows for ejector control with a single communication line
    Reading of the device information and parameter batch settings are possible.
  • Compatible with ejector systems and vacuum pump systems
  • Energy saving ejector
    Air supply is cut-off when vacuum is reached.
    Air consumption: 93% reduction (Under SMC’s measurement conditions)
  • More efficient ejector: Suction flow increased by 50%
    (Compared to other SMC 1-stage ejectors)
  • Energy saving efficiency: 93% reduction
  • Improved low noise and suction flow by adoption of a high-noise reduction silencer

Electric Gripper for Collaborative Robots LEHR Series

Updated Jan-24

  • Can be used with the collaborative robots of UNIVERSAL ROBOTS, FANUC CORPORATION, and OMRON/TECHMAN ROBOT
  • 2 variations are available.
  • Gripping force: 60 to 140 N
  • Operate by simply connecting 1 electrical wire
  • Annual CO2 emissions reduced by up to 52% through motor control optimization (SMC comparison)
  • With internal battery-less absolute encoder
  • Easy tool changing (Manual changer)
  • Compatible plug-in software: URCap

Wear Resistant Tubing/Clear Type TUZC Series

Updated Jan-24

  • Abrasion: Approx. 1/3
    (Compared with SMC polyurethane tubing TU series)
  • Clear type
    Transparency in which the inside contents of a tube can be seen.

Flow Controller for Air PFCA7 Series

Updated Jan-24

  • For the automatic adjustment of the flow rate
  • Applicable fluid: Dry air, N2, Ar, CO2
  • Color display/2-screen display supported
    For the confirmation of the instantaneous flow rate, flow rate command value, and accumulated flow rate at a glance
  • IO-Link compatible
  • Flow ratio 100:1

3-Screen Display High-Precision Digital Pressure Switch ZSE20□(F)/ISE20□ Series

Updated Dec-23

  • An M12 connector type has been added to the 20B series. [New]
  • A low pressure range type has been added to the 20A series. [New]
  • An IO-Link compatible type has been added to the 20C series for general fluids.
  • Visualization of settings
  • Simple 3-step setting
  • Easy screen switching
  • Delay time:1.5 ms or less
  • Current consumption: 25 mA or less

Water Resistant Stainless Steel Speed Controller HF2A-ASG-□V Series

Updated Dec-23

  • The water-resistant construction and the stainless steel external parts allow for the product to be used in environments where it may come into contact with water droplets.
  • Metal material: External metal parts stainless steel 316✳︎1
    *1 Stainless steel 304 (external metal parts excluding body A)
  • Grease: NSF H1 grease
  • Max. operating temperature: 150°C
  • mproved water-resistance and washabili

Vacuum Filter AFJ-D Series

Updated Dec-23

  • Prevents vacuum equipment trouble
  • Nominal filtration rating:5,40,80μm
  • Large flow capacity:max.660L/min(ANR)
  • Elements can be reused by washing them.
  • Water drops can be removed.∗
  • The bowl is covered with a transparent bowl guard

Push-lock Type Dual Speed Controller with One-touch Fitting ASD-A Series

Updated Dec-23

  • Easy to lock push-lock type
  • No tools required. Larger knob
  • Allows for simultaneous meter-in and meter-out control
  • Prevents cylinders from popping out, and allows for the speed control of single acting cylinders
  • Easy identification of meter-in or meter-out by knob color
  • Lightweight: Approx. 28% lighter
  • Improved reproducibility of flow rate

Vacuum Pad/Bowl Shape with Non-slip Feature ZP3M Series

Updated Dec-23

  • A bowl bellows shape has been added. [New]
  • Non-slip special ribs
    Diagonal ribs are radially arranged to secure the gripping force in all directions.
    ・Prevents workpiece slippage
    ・Secure adsorbing and transferring are possible.
  • Bowl shape with excellent flexibility
    Curved workpieces can also be adsorbed.
    The pad follows the workpiece shape, making stable adsorption possible.
  • Horizontal holding force: 231 N (Pad diameter ø80)
  • Suitable for high-temperature workpieces (200°C)
  • Material: FS61 (Fluoro-based rubber) improves abrasion resistance
    ∗ More than twice the abrasion resistance of SMC's urethane pads
  • Suitable for workpieces with oil film
    As oil is ejected to the grooves between special ribs, the lateral slipping of workpiece can be suppressed even on a steel plate with oil film.

Multistage Ejector ZL1/ZL3/ZL6 Series

Updated Dec-23

  • An N.O. specification has been added to the pressure switch for vacuum with energy saving function. [New]
    Can hold vacuum∗ even when the power goes out or is turned off
    Prevents the sudden dropping of workpieces∗
    ∗ Supposing the supply pressure is being maintained
  • An IO-Link compatible vacuum pressure switch has been added. [New]
    Allows for ejector control with a single communication line
    Reading of the device information and parameter batch settings are possible.
  • Max. suction flow rate: 3 types available: 100, 300, and 600 L/min (ANR)
  • Air consumption: 91% reduction (For the ZL3, ZL6)
  • Weight: Max. 60% reduction [ZL112 (Existing model): 450 g → ZL1: 180 g]

Flow Sensor PFMV5/PFGV301 Series

Updated Dec-23

  • 3-screen display digital flow monitor PFGV301 series [New]
  • A measuring flow rate range of 0.0 to 0.1 L/min (-X502) [New]
    has been added.
  • For suction verification of very small workpieces
    The flow sensor enables more reliable suction verification than a pressure sensor.
  • Repeatability: ±2% F.S.
  • Response speed: 5 ms or less
  • Withstand pressure: 500 kPa
  • Grease-free

3-Color Display Digital Flow Switch for Water PF3W Series

Updated Dec-23

  • Output specification variations have been added. [New]
    PF3W7: Analog voltage 2-output type (flow rate + temperature)
        Analog current 2-output type (flow rate + temperature)
  • 3-screen display 4-channel flow monitor PFG200 series [New]
  • 3-color/2-screen display
  • Integrated temperature sensor
  • 40% smaller than the existing product
  • IP65 compliant, Non-grease type
  • Fluid temperature: 0 to 90°C
  • PVC piping type: Applicable to deionized water, chemical liquids, etc.
  • IO-Link compatible (Made to order)

Compact Vacuum Unit Ejector System/Vacuum Pump System ZQ□A Series

Updated Dec-23

  • An IO-Link compatible pressure switch has been added. [New]
    Allows for ejector control with a single communication line
    Reading of the device information and parameter batch settings are possible.
  • Vacuum pressure switch with energy saving function
    Air consumption: 90% reduction (Based on SMC’s measurement conditions)
    Power consumption: 60% reduction [1 W (Existing model) → 0.4 W]
    Vacuum release pressure: From 0 MPa [From 0.3 MPa (Existing model) → From 0 MPa]
    Copy function: Reduced setting labor, Minimized risk of setting mistakes
  • Compatible with ejector systems and vacuum pump systems

Flow Controller for Water FC3W Series

Updated Dec-23

  • For the stepless control of water flow rate in proportion to electrical signals
  • Flow rate control accuracy: ±5% F.S.
  • Response time: 10 s or less
  • Grease-free

3-Color Display Digital Flow Switch for Water PF3W-Z/L Series

Updated Nov-23

  • Output specification variations have been added. [New]
    PF3W7-Z: Analog voltage 2-output type (flow rate + temperature)
         Analog current 2-output type (flow rate + temperature)
  • Compatible with the PFG200 series 3-screen display 4-channel flow monitor [New]
  • Applicable fluid: Water, Ethylene glycol aqueous solution
  • Lightweight: Max. 53% reduction (40 L/min, With temperature sensor)
  • IO-Link compatible
  • 3-color/2-screen display
  • Compatible with the temperature sensor & flow adjustment valve
  • Fluid temperature: 0 to 90°C

Electric Actuator/Large Slider Type, Belt Drive LET-X11 Series

Updated Oct-23

  • Max. work load: 240 kg (Size 100)/75 kg (Size 80)
  • Stroke: Up to 3000 mm (Standard)
  • Max. speed [mm/s]: 4000 (Size 100), 2160 (Size 80)
  • Max. acceleration/deceleration [mm/s2]: 20000
  • Simplified belt replacement
  • Solid state auto switches are mountable.

Plug-in Electro-Pneumatic Regulator / Manifold Type IITV23 Series

Updated Oct-23

  • Connects the electro-pneumatic regulator and the fieldbus device to the same manifold.
    This results in reduced wiring, less man hours for piping and a more compact size.
  • Compact
    Installation area: 20% reduction, Occupied volume: 10% reduction
  • Gain setting
  • Sensitivity setting
  • Remote control and monitoring are available.

Air Saving Impact Blow Valve IBV Series

Updated Oct-23

  • Increased impact force due to higher peak pressure
  • Instantaneous air blow reduces CO2, air consumption, and operation time
    Peak pressure: 2 to 3 times or more
    CO2/Air consumption: 93% reduction
    Operation time: 97% reduction

Proportional Control Valve JSP Series

Updated Oct-23

  • Control the flow rate smoothly according to the current
  • Repeatability: ±3% F.S. or less
  • Sensitivity: 2% F.S. or less
  • 2 body types: Body ported, Base mounted
  • IP67 enclosure
  • Seal material: FKM
  • Choice of body material: Stainless steel, Brass
  • Electrical entry: Grommet, Conduit, DIN terminal

Electro-Pneumatic Regulator / High Flow Rate ITV1100/2100/3100 Series

Updated Oct-23

  • For the stepless control of air pressure in proportion to electrical signals
  • Flow rate: Max. approx. 5 times
    (Compared with the existing model)
  • Sensitivity: ±0.2% F.S. or less
  • Linearity: ±1% F.S. or less
  • Hysteresis: 0.5% F.S. or less

Compact Compressor CRP Series

Updated Oct-23

  • Supplies compressed air in an environment with no air source such as cobots, AGV and AMRs
  • Compact: 154 mm (Width) x 134 mm (Height) x 100 mm (Depth)
  • Lightweight: 3.5 kg (Compressor: 3.1 kg, Controller: 0.4 kg)
  • A single unit can be used to provide positive or vacuum pressure (vacuum pump).
    Max. discharge pressure: 0.55 MPa
    Ultimate vacuum pressure: −70 kPa
  • Oil-free
  • Noise: 55 dB or less (When the silencer ANB1-01 is installed)
    (When supplying positive pressure)
  • Max. flow rate of 10 L/min (ANR)

Modular Connection Type Compressed Air Preparation Filter/Activated Carbon Filter AFF/AM/AMD/AMK Series

Updated Sep-23

  • With clogging switch (Excludes the AMK)[New]
  • An element service indicator has been added.
    (Excludes the AMK)
  • Compressed air purity class: ISO 8573
  • Weight reduced by 50%
    AFF/AM□20: 0.19 kg (Existing model: 0.38 kg)
  • Face-to-face and depth dimensions reduced by 30%
  • The increased air flow capacity due to a reduced pressure drop contributes to energy saving.
    Flow capacity increased by 50%
    Pressure drop reduced by up to 50%

4-Port Solenoid Valve Cassette Type Manifold SJ1000/2000/3000/4000 Series

Updated Sep-23

  • A large flow type (SJ3000A) has been added.[New]
  • An SJ4000 manifold has been added.[New]
  • Allows for the mixed mounting of 5 SJ series valve sizes
  • Connector type (Card edge type)
    Easily increase or decrease the number of stations and easily replace valves
  • Non plug-in individual wiring compliant

Flow Controller for Air PFCQ Series

Updated Sep-23

  • Flow rate control range: 9 to 300 L/min
    * Operational differential pressure range: 0.05 to 0.5 MPa
  • Time to reach the set flow rate: 0.5 seconds or less
    (When the operating differential pressure is 0.3 MPa and the flow rate is set to 300 L/min)
  • Flow rate accuracy: ±3% F.S.
  • Grease-free
  • Lightweight 850 g
  • 3-screen display digital flow monitor PFG310-X105

Air Grippers for Collaborative Robots RMH□ Series

Updated Sep-23

  • Unitization of the peripheral devices required for gripper driving
    Operation is possible simply by connecting 1 air supply tube and
    1 electrical wire.
    Built-in solenoid valve, exhaust throttle valve with silencer, auto switch, fitting, etc.
  • 3 types of grippers available for use with a variety of workpieces
  • Can be used with the collaborative robots of 12 companies
  • Manual changer built in as standard
    Allows for easy tool changing and labor saving
  • Air consumption reduced by up to 80%

Direct Operated 2-Port Solenoid Valve HF3-JSX

Updated Aug-23

  • NSF/ANSI 61 certification
  • IP67 enclosure
  • Space saving
    Compact: Valve volume reduced by 25% (Compared with the existing model)
    Lightweight: Weight reduced by 30% (Compared with the existing model)
  • Body material: Stainless steel

[Model with Residual Pressure Release Function]
Speed Controller with Pilot Check Valve ASP Series

Updated Jul-23

  • A stainless steel type (ASP-G series) has been added.
    For secondary battery manufacturing processes [New]
  • Model with residual pressure release function: It is possible to construct a safety circuit.
  • Model without residual pressure release function: Temporary intermediate stops are possible.
  • Vertical and horizontal types are available, which can be selected depending on the installation conditions.
  • Improved piping design flexibility (360°-rotation type)

Modular Connection Type Membrane Air Dryer IDG-D Series

Updated Jul-23

  • Compatible with various ISO water quality classes
  • Modular connection is possible.
  • Non-fluorocarbon
  • Power supply not required
  • No vibration or heat discharge
  • Contributes to energy saving
    Pressure drop reduced by up to 61%
    Outlet air flow rate Max. 25% increase
    Purge ratio: Approx. 14%

Valve Manifold Integrated with Ejector System JSY1000-E Series

Updated Jul-23

  • A vacuum release flow adjustment unit has been added. [New]
  • Compact All-in-One Manifold
    The devices have been integrated into one for applications in which an actuator and vacuum suction are used together.
  • EtherCAT®,IO-Link,PROFINET® compatible
  • Wiring/Piping Saving through Use of All-in-One Manifold
  • Installation area: 64%reduction
  • Weight: 42%reduction
  • Energy Saving Function
    CO2emissions (Air consumption) : 90% reduction

Longer Life Cylinder CXS2-XB24

Updated Jul-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CXS2 Dual Rod Cylinder series

[For High-Pressure Water] Pilot Operated 2-Port Solenoid Valve JSXH-X2

Updated Jul-23

  • Can be used at up to 10 MPa
    For high-pressure washing, water spraying, and misting
  • An IP67 structure with improved environmental resistance (The DIN terminal is IP65.)
  • Orifice diameter [mmø]: 12
  • Flow rate characteristics [Kv]: 1.7 (Port size 3/8), 1.9 (Port size 1/2)
  • Easy maintenance
    The coil can be replaced by simply removing the clip.
  • Power consumption: 8 W

Pulse Valve Valve for Dust Collector JSXF/JSXFA Series

Updated Jul-23

  • A SMARTVENT type has been added. [New]
    The integrated control board eliminates the need for a control box.
  • Life: 10 million cycles or more/10 times or more
  • High peak pressure and low air consumption
    Peak pressure: 15% increase, Air consumption: 35% reduction
  • Fluid temperature: −40 to 60°C
    Can be used in a wide range of temperatures

Modular F.R.L. Units AC Series

Updated Jul-23

  • A right angle square type pressure gauge and various attachments have been added. [New]
  • Modular Design with Uniform Body Style
  • Better visibility & environmental resistance
    2-layer construction: The bowl is covered with a transparent bowl guard!
    Better visibility: 360°
  • No tools are required.
    Easier replacement of the element (AF20-D to AF40-D only)

OSHA Standard Compliant Nozzle for One-touch Fitting KNA(G)-Q10-180

Updated Jun-23

  • Compliant with OSHA Standard 1910.242(B)
    The structure prevents closing of the discharge port.
    This is a safety design that limits the pressure to 30 psi even when an operator is touching the nozzle.
    (Operating pressure: 0.5 MPa or less)
  • CO2 emissions (Air consumption): 42% reduction
  • Low noise: Max. 8 dB(A) reduction
    ∗ Compared with the existing model: nozzle for One-touch fitting (resin type) KN-Q10A-200

3-Screen Display 4-Channel Flow Monitor PFG200 Series

Updated Jun-23

  • Up to 4 flow sensors can be connected!
  • It is possible to change the settings while checking the measured value.
  • Centralized control saves installation space.
    66% reduction in installation space (Compared with the panel mounted PFG20□)
  • Accumulated flow measurement
    A single product can manage the accumulated flow in four lines.
  • A single monitor various applications
    3 channels are displayed simultaneously. (Customer defined channel can be set.)

Longer Life Cylinder CUJ-XB24

Updated May-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CUJ Mini Free Mount Cylinder series

Bernoulli Gripper with Coanda Grip ZNC-C Series

Updated Apr-23

  • Reduces the impact of air flow on light-weight workpieces and adjacent workpieces
  • Prevents lateral slide when suctioning the workpiece
    There is no risk of suctioning of powder matter adhering on the workpiece into the device and pipe, as the workpiece is suctioned while air is blow.
  • Body material: Stainless steel, Aluminum
  • With Coanda grip
    Prevents blowing away of workpiece before suctioning and lateral sliding of workpiece during suctioning

Magnetically Coupled Rodless Cylinder/Basic Type ø6, ø10, ø15, ø20, ø25, ø32, ø40, ø50, ø63 CY3B Series

Updated Apr-23

  • Lightweight
    The product weight has been reduced through re-designing of the body and head cover shapes and employment of magnetic coupling.
    Weight: 16% reduction (1.35 kg → 1.13 kg)
  • Improved lubrication
    A Lube-retainer is installed to support lubrication retention on the piston and to ensure a lubrication film. (Bore size: ø15 to ø63)
  • Stable operation
    Lengthening of the wear ring on the body side by, 30% at maximum, helps to achieve smooth movement.
  • Lengthening of the wear ring on the body side by, 30% at maximum, helps to achieve smooth movement.

Air Slide Table/High Rigidity Type ø32 MXQ32-X2600

Updated Apr-23

  • 75, 100, 125, and 150 mm strokes have been added. [New]
  • A linear guide with a 4-row circular arc groove for high rigidity and high precision
  • Table displacement: Reduced by 50% (0.022mm→0.011mm)
  • Max. load weight: 16 kg
  • Aluminum table:
    Load weight increased by reducing the weight of moving parts
  • Integrated pilot port, stroke adjuster, and auto switch on 1 side allows for improved operability

Plug-in Bottom Ported Manifold with Stainless Steel Plate JSY3000-S Series

Updated Mar-23

  • Bottom seal/stainless steel plate prevents the flooding of valves.
  • Wiring
    D-sub connector/Flat ribbon cable/Terminal block box/Lead wire/Serial unit (EX600, EX245, EX250, EX260)
  • Compatible with EtherNet/IP™ and IO-Link

Compact Type Speed Controller with Indicator JAS-SML/SCL Series

Updated Mar-23

  • Improvement of resolution has made it possible to make fine adjustment.
    1〜50mm/s:JAS-SML Series
    50〜150mm/s:JAS-SCL Series
  • Height: Max. 20.8 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes

Longer Life Cylinder CJ2-XB24

Updated Mar-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models, CJ2 Air Cylinder series

Longer Life Cylinder CQS-XB24

Updated Mar-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CQS Compact Cylinder series

Angle Seat Valve / Air Operated Type JSB Series

Updated Mar-23

  • Low pressure loss due to angle seat structure!
  • Long service life: 10 million cycles (Air, Water), 3 million cycles (Steam)
  • Large flow rate
    A large flow rate is possible due to the optimized flow channel shape. (Cv factor: approx. 2.5 times)
  • Compact: Height 166 mm (Port size: 1")
  • Abundant series variations of 7 sizes
  • All-in-One (Stainless steel 316L equivalent)
    Air, Water, Steam

Dual Rod Cylinder ø6, ø10, ø16, ø20, ø25, ø32 CXS2 Series

Updated Mar-23

  • Allowable kinetic energy: 0.016 J (7 times that of the existing model)
  • Max. piston speed: 800 mm/s (2.6 times that of the existing model)
  • Max. standard stroke increased
  • Mounting dimensions are compatible with the existing CXS series products.
  • Double piston construction provides twice the output force.
  • Non-rotating accuracy of ±0.1° because of the dual rod construction

Compact Type Speed Controller with Indicator JAS-S Series

Updated Mar-23

  • Height: Max. 20.8 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Mounting stud is available on the left side or the right side.

Metal Speed Controller with Indicator ASB-□H Series

Updated Mar-23

  • Improved environmental resistance with the all metal exterior [With indicator]
    For use in environment with welding spatter (Option BH type)
    Contributes to reducing setting time and errors by allowing the user to adjust flow rate before mounting and operating the cylinder
  • Possible to manage the flow rate values using an indicator!
  • Flow adjustable with a hexagon wrench tool
    Prevents accidental manual operation
  • Adjustment needle lock nut feature as standard
    Prevents unauthorized adjustment and unwanted operation of the needle from the set position due to vibrations or impacts.
    Helps improve safety in your machinery.
  • 2 types are available for different applications.
    For welding environments and for general environments

Thermo-chiller/Low-temperature Type HRS040-A-20-T1-X158/X164

Updated Mar-23

  • Supports low temperatures of as low as −10°C
  • Compact: Equivalent in size to the HRS040
  • Cooling capacity: 1 kW (At −10°C)
  • Temperature stability: ±0.1°C
  • Set temperature range: −10°C to 40°C

Speed Controller with Compact Indicator AS-FSA Series

Updated Mar-23

  • Body sizes 1/8, 1/4, 3/8, and 1/2 have been added. [New]
  • Height: Max. 5.5 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Better visibility
    Check from 360° directions is possible.
     Inspection and maintenance works are facilitated.

Speed Controller with Compact Indicator AS-FSMA/FSCA Series

Updated Mar-23

  • Body size 1/4 has been added. [New]
  • Improvement of resolution has made it possible to make fine adjustment.
    1 to 50 mm/s: AS-FSMA series
    50 to 150 mm/s: AS-FSCA series
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Better visibility
    Check from 360° directions is possible.
    Inspection and maintenance works are facilitated.

Deceleration Controller DAS Series

Updated Feb-23

  • 2-speed control reduces cycle time
    Allows for the impact relaxation of the stroke end
     Allows for the 2-speed control of cylinders
    The deceleration position (cushion timing) and 2nd speed (cushion intensity) can be adjusted.
  • Possible to control flow rate values using an adjustment handle with graduations
  • Space saving
     Maximum 76% reduction of occupying space (196cm3 ← 811cm3)

Grippers for Collaborative Robots ZXP7-PFL1-□-X1, JMHZ2-X7500-KR for KAWADA ROBOTICS CORPORATION, NEXTAGE

Updated Feb-23

    Cups with Flange

  • Standards: Conforming to ISO9409-1-50-4-M6
  • Tube-less piping
    Individual piping to suction cups is unnecessary and there is no interference with workpieces or operators
  • A wide variety of cup variations are available to support a wide range of workpieces.

  • Air Gripper

  • Compact, lightweight product with high gripping force due to air operation
  • An air gripper that realizes high rigidity and high precision due to its guide-integrated construction
  • With high-precision linear guide
  • Repeatability: ±0.01 mm
  • Standards: Conforming to ISO9409-1-50-4-M6

Air Saving Impact Blow Gun IBG Series

Updated Feb-23

  • An adjuster with indicator has been added. (With protective cover) [New]
  • A compact type (IBG2 series) has been added. [New]
  • Increased impact force due to higher peak pressure
  • Instantaneous air blow reduces air consumption and operation time.
  • Air consumption: 87% reduction

Vacuum Pad / Bellows Type ZP3P-JT Series

Updated Feb-23

  • A flat attachment has been added. (2.5-stage)[New]
    For reducing wrinkles
  • For the adsorption transfer of workpieces with flexible soft film packaging
  • Thin film skirt and special shaped ribs
  • The pad and attachment are made of materials compliant with FDA
    (U.S. Food and Drug Administration) regulations as well as Japan Food Sanitation Act standards.
  • Blue colored pad
    Easy to distinguish the vacuum pad by color during
    contamination inspection

Vacuum Flow ZHV Series

Updated Jan-23

  • Blow and vacuum can be performed by supplying compressed air.
    Blow flow rate: Max. 6820 L/min (ANR)∗1
    Vacuum flow rate: Max. 5270 L/min (ANR)∗1
    ∗1 Values for the ZHV40 when the supply pressure is 0.5 MPa
  • It is possible to adjust the blow and vacuum flow rate by adjusting the nozzle position!
  • A vacuum flow rate 3 times or more the supply air ∗2
    ∗2 Excludes the ZHV10
  • A blow flow rate 4 times or more the supply air ∗2
    ∗2 Excludes the ZHV10
  • Weight: Max. 50% reduction (209 g ← 417 g)∗3
    ∗3 ZHV20, in comparison with product (ZH20-X185)
  • Volume: Max. 50% reduction (17000 mm3 ← 34000 mm3) ∗4
    ∗4 ZHV10, in comparison with product (ZH10-X185)
  • In terms of body mounting, port connection, and passage diameter, this product is compatible with the product (ZH-X185).

Longer Life Cylinder MGJ-XB24

Updated Jan-23

  • New technology offers at least 4 times better durability.
  • Employs the same specification and mounting dimensions as the existing models,
    MGJ Miniature Guide Rod Cylinder series

Bernoulli Gripper ø20, ø30, ø40, ø60, ø80 ZNC Series

Updated Jan-23

  • Body size ø20 has been added. [New]
  • For the adsorption transfer of thin cloths, films, printed circuit boards, etc.
  • Energy saving: Max. 79% reduction
    (Comparison of air consumption to lifting force)
  • High lifting force: 65 N
    10.3 times that of the existing model
    (Existing model: 6.3 N → ZNC80: 65 N)
  • 3 types of body materials: Aluminum, Resin, Stainless steel
  • Attachment
    With stopper: Prevents workpiece slippage
    With vibration suppression cover: Suppresses the vibration noise of thin workpieces

Go Top