New products

Product Information »  New Products List

New Products List

3-Screen Display Condensation Checker (Digital Temperature & Humidity Switch) PSH Series

New

Updated Dec-23

  • Visualization of relative humidity
    Real-time digital display
  • Remote/Condition monitoring
    Remote confirmation via switch output preventing condensation problems!

Flow Controller for Water FC3W Series

New

Updated Dec-23

  • For the stepless control of water flow rate in proportion to electrical signals
  • Flow rate control accuracy: ±5% F.S.
  • Response time: 10 s or less
  • Grease-free

3-Color Display Digital Flow Switch for Water PF3W-Z/L Series

New

Updated Nov-23

  • Output specification variations have been added. [New]
    PF3W7-Z: Analog voltage 2-output type (flow rate + temperature)
         Analog current 2-output type (flow rate + temperature)
  • Compatible with the PFG200 series 3-screen display 4-channel flow monitor [New]
  • Applicable fluid: Water, Ethylene glycol aqueous solution
  • Lightweight: Max. 53% reduction (40 L/min, With temperature sensor)
  • IO-Link compatible
  • 3-color/2-screen display
  • Compatible with the temperature sensor & flow adjustment valve
  • Fluid temperature: 0 to 90°C

Compact Slide ø6, ø10, ø16, ø20 MXH2 Series

New

Updated Oct-23

  • Improved linear guide rigidity reduces the amount of table displacement by 48%
    Displacement due to a force acting in the pitch direction: 48% reduction (0.31 mm→0.16 mm)
    Displacement due to a force acting in the yaw direction: 63% reduction (0.24 mm→0.09 mm)
    Displacement due to a force acting in the roll direction: 90% reduction (0.06 mm→0.006 mm)
  • Max. standard stroke: 150 mm (For ø20)
  • Weight: Max. 6% reduction (194 g→182 g)
  • Dimensions for mounting and length are equivalent to the existing MXH series.

Electric Actuator/Large Slider Type, Belt Drive LET-X11 Series

New

Updated Oct-23

  • Max. work load: 240 kg (Size 100)/75 kg (Size 80)
  • Stroke: Up to 3000 mm (Standard)
  • Max. speed [mm/s]: 4000 (Size 100), 2160 (Size 80)
  • Max. acceleration/deceleration [mm/s2]: 20000
  • Simplified belt replacement
  • Solid state auto switches are mountable.

Plug-in Electro-Pneumatic Regulator / Manifold Type IITV23 Series

New

Updated Oct-23

  • Connects the electro-pneumatic regulator and the fieldbus device to the same manifold.
    This results in reduced wiring, less man hours for piping and a more compact size.
  • Compact
    Installation area: 20% reduction, Occupied volume: 10% reduction
  • Gain setting
  • Sensitivity setting
  • Remote control and monitoring are available.

Air Saving Impact Blow Valve IBV Series

New

Updated Oct-23

  • Increased impact force due to higher peak pressure
  • Instantaneous air blow reduces CO2, air consumption, and operation time
    Peak pressure: 2 to 3 times or more
    CO2/Air consumption: 93% reduction
    Operation time: 97% reduction

Proportional Control Valve JSP Series

New

Updated Oct-23

  • Control the flow rate smoothly according to the current
  • Repeatability: ±3% F.S. or less
  • Sensitivity: 2% F.S. or less
  • 2 body types: Body ported, Base mounted
  • IP67 enclosure
  • Seal material: FKM
  • Choice of body material: Stainless steel, Brass
  • Electrical entry: Grommet, Conduit, DIN terminal

Electro-Pneumatic Regulator / High Flow Rate ITV1100/2100/3100 Series

New

Updated Oct-23

  • For the stepless control of air pressure in proportion to electrical signals
  • Flow rate: Max. approx. 5 times
    (Compared with the existing model)
  • Sensitivity: ±0.2% F.S. or less
  • Linearity: ±1% F.S. or less
  • Hysteresis: 0.5% F.S. or less

Compact Compressor CRP Series

New

Updated Oct-23

  • Supplies compressed air in an environment with no air source such as cobots, AGV and AMRs
  • Compact: 154 mm (Width) x 134 mm (Height) x 100 mm (Depth)
  • Lightweight: 3.5 kg (Compressor: 3.1 kg, Controller: 0.4 kg)
  • A single unit can be used to provide positive or vacuum pressure (vacuum pump).
    Max. discharge pressure: 0.55 MPa
    Ultimate vacuum pressure: −70 kPa
  • Oil-free
  • Noise: 55 dB or less (When the silencer ANB1-01 is installed)
    (When supplying positive pressure)
  • Max. flow rate of 10 L/min (ANR)

Modular Connection Type Compressed Air Preparation Filter/Activated Carbon Filter AFF/AM/AMD/AMK Series

Updated Sep-23

  • With clogging switch (Excludes the AMK)[New]
  • An element service indicator has been added.
    (Excludes the AMK)
  • Compressed air purity class: ISO 8573
  • Weight reduced by 50%
    AFF/AM□20: 0.19 kg (Existing model: 0.38 kg)
  • Face-to-face and depth dimensions reduced by 30%
  • The increased air flow capacity due to a reduced pressure drop contributes to energy saving.
    Flow capacity increased by 50%
    Pressure drop reduced by up to 50%

Wireless System EXW1/EX600-W Series

Updated Sep-23

  • EtherCat has been added to the compact type EXW1 series. [New]
  • Noise resistance
     Uses the 2.4 GHz ISM frequency band
     Frequency hopping: Every 2 ms (Fastest)
  • Communication cables not required
    Reduced wiring work, space, and cost
    Minimized disconnection risk
  • Provides communication stability in FA environments
  • Compact and lightweight (EXW1)
    Volume: Approx. 86% reduction, Weight: Approx. 87% reduction
  • Modular connection is possible. (EX600-W)

4-Port Solenoid Valve Cassette Type Manifold SJ1000/2000/3000/4000 Series

Updated Sep-23

  • A large flow type (SJ3000A) has been added.[New]
  • An SJ4000 manifold has been added.[New]
  • Allows for the mixed mounting of 5 SJ series valve sizes
  • Connector type (Card edge type)
    Easily increase or decrease the number of stations and easily replace valves
  • Non plug-in individual wiring compliant

Flow Controller for Air PFCQ Series

Updated Sep-23

  • Flow rate control range: 9 to 300 L/min
    * Operational differential pressure range: 0.05 to 0.5 MPa
  • Time to reach the set flow rate: 0.5 seconds or less
    (When the operating differential pressure is 0.3 MPa and the flow rate is set to 300 L/min)
  • Flow rate accuracy: ±3% F.S.
  • Grease-free
  • Lightweight 850 g
  • 3-screen display digital flow monitor PFG310-X105

Air Grippers for Collaborative Robots RMH□ Series

Updated Sep-23

  • Unitization of the peripheral devices required for gripper driving
    Operation is possible simply by connecting 1 air supply tube and
    1 electrical wire.
    Built-in solenoid valve, exhaust throttle valve with silencer, auto switch, fitting, etc.
  • 3 types of grippers available for use with a variety of workpieces
  • Can be used with the collaborative robots of 12 companies
  • Manual changer built in as standard
    Allows for easy tool changing and labor saving
  • Air consumption reduced by up to 80%

Direct Operated 2-Port Solenoid Valve HF3-JSX

Updated Aug-23

  • NSF/ANSI 61 certification
  • IP67 enclosure
  • Space saving
    Compact: Valve volume reduced by 25% (Compared with the existing model)
    Lightweight: Weight reduced by 30% (Compared with the existing model)
  • Body material: Stainless steel

[Model with Residual Pressure Release Function]
Speed Controller with Pilot Check Valve ASP Series

Updated Jul-23

  • A stainless steel type (ASP-G series) has been added.
    For secondary battery manufacturing processes [New]
  • Model with residual pressure release function: It is possible to construct a safety circuit.
  • Model without residual pressure release function: Temporary intermediate stops are possible.
  • Vertical and horizontal types are available, which can be selected depending on the installation conditions.
  • Improved piping design flexibility (360°-rotation type)

Modular Connection Type Membrane Air Dryer IDG-D Series

Updated Jul-23

  • Compatible with various ISO water quality classes
  • Modular connection is possible.
  • Non-fluorocarbon
  • Power supply not required
  • No vibration or heat discharge
  • Contributes to energy saving
    Pressure drop reduced by up to 61%
    Outlet air flow rate Max. 25% increase
    Purge ratio: Approx. 14%

Valve Manifold Integrated with Ejector System JSY1000-E Series

Updated Jul-23

  • Compact All-in-One Manifold
    The devices have been integrated into one for applications in which an actuator and vacuum suction are used together.
  • EtherCAT®compatible
  • Wiring/Piping Saving through Use of All-in-One Manifold
  • Installation area: 64%reduction
  • Weight: 42%reduction
  • Energy Saving Function
    CO2emissions (Air consumption) : 90% reduction

Longer Life Cylinder CXS2-XB24

Updated Jul-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CXS2 Dual Rod Cylinder series

[For High-Pressure Water] Pilot Operated 2-Port Solenoid Valve JSXH-X2

Updated Jul-23

  • Can be used at up to 10 MPa
    For high-pressure washing, water spraying, and misting
  • An IP67 structure with improved environmental resistance (The DIN terminal is IP65.)
  • Orifice diameter [mmø]: 12
  • Flow rate characteristics [Kv]: 1.7 (Port size 3/8), 1.9 (Port size 1/2)
  • Easy maintenance
    The coil can be replaced by simply removing the clip.
  • Power consumption: 8 W

Pulse Valve Valve for Dust Collector JSXF/JSXFA Series

Updated Jul-23

  • A SMARTVENT type has been added. [New]
    The integrated control board eliminates the need for a control box.
  • Life: 10 million cycles or more/10 times or more
  • High peak pressure and low air consumption
    Peak pressure: 15% increase, Air consumption: 35% reduction
  • Fluid temperature: −40 to 60°C
    Can be used in a wide range of temperatures

Modular F.R.L. Units AC Series

Updated Jul-23

  • A right angle square type pressure gauge and various attachments have been added. [New]
  • Modular Design with Uniform Body Style
  • Better visibility & environmental resistance
    2-layer construction: The bowl is covered with a transparent bowl guard!
    Better visibility: 360°
  • No tools are required.
    Easier replacement of the element (AF20-D to AF40-D only)

Air Flow Controller IN502-44/45

Updated Jun-23

  • Automatic flow rate adjustment is possible.
  • Dry air, N2
  • Control accuracy: ±5% F.S.
  • Responsiveness: 0.5 s or less
  • Space saving/Reduced piping, wiring, and installation labor
  • Various types of grease can be selected.
    Grease compatible with low dew points, White vaseline, Grease for food
  • IO-Link compatible

OSHA Standard Compliant Nozzle for One-touch Fitting KNA(G)-Q10-180

Updated Jun-23

  • Compliant with OSHA Standard 1910.242(B)
    The structure prevents closing of the discharge port.
    This is a safety design that limits the pressure to 30 psi even when an operator is touching the nozzle.
    (Operating pressure: 0.5 MPa or less)
  • CO2 emissions (Air consumption): 42% reduction
  • Low noise: Max. 8 dB(A) reduction
    ∗ Compared with the existing model: nozzle for One-touch fitting (resin type) KN-Q10A-200

3-Screen Display 4-Channel Flow Monitor PFG200 Series

Updated Jun-23

  • Up to 4 flow sensors can be connected!
  • It is possible to change the settings while checking the measured value.
  • Centralized control saves installation space.
    66% reduction in installation space (Compared with the panel mounted PFG20□)
  • Accumulated flow measurement
    A single product can manage the accumulated flow in four lines.
  • A single monitor various applications
    3 channels are displayed simultaneously. (Customer defined channel can be set.)

3-Screen Display High-Precision Digital Pressure Switch ZSE20□(F)/ISE20□ Series

Updated May-23

  • An IO-Link compatible type has been added to the 20C series for general fluids. [New]
  • A low pressure range type has been added to the 20A series. [New]
  • Visualization of settings
  • Simple 3-step setting
  • Easy screen switching
  • Delay time:1.5 ms or less
  • Current consumption: 25 mA or less

Longer Life Cylinder CUJ-XB24

Updated May-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CUJ Mini Free Mount Cylinder series

Air Management System AMS20/30/40/60 Series

Updated Apr-23

  • EtherCAT has been added as a communication protocol. [New]
  • Made to order added. [New]
    Without residual pressure relief 3-port solenoid valve
    specification (-X101)
    Without standby regulator specification (-X102)
  • Air consumption: Max. 62% reduction
    Monitors the machine standby conditions (when production stops) and automatically decreases the pressure.
    Reduces unnecessary air consumption
  • Compatible with OPC UA
    Direct connection enables data communications.
  • Compatible with wireless systems
    Communication cables not required
    High security thanks to unique encryption
    Communication distance: Max. 100 m
  • IO-Link compatible

Bernoulli Gripper with Coanda Grip ZNC-C Series

Updated Apr-23

  • Reduces the impact of air flow on light-weight workpieces and adjacent workpieces
  • Prevents lateral slide when suctioning the workpiece
    There is no risk of suctioning of powder matter adhering on the workpiece into the device and pipe, as the workpiece is suctioned while air is blow.
  • Body material: Stainless steel, Aluminum
  • With Coanda grip
    Prevents blowing away of workpiece before suctioning and lateral sliding of workpiece during suctioning

Magnetically Coupled Rodless Cylinder/Basic Type ø6, ø10, ø15, ø20, ø25, ø32, ø40, ø50, ø63 CY3B Series

Updated Apr-23

  • Lightweight
    The product weight has been reduced through re-designing of the body and head cover shapes and employment of magnetic coupling.
    Weight: 16% reduction (1.35 kg → 1.13 kg)
  • Improved lubrication
    A Lube-retainer is installed to support lubrication retention on the piston and to ensure a lubrication film. (Bore size: ø15 to ø63)
  • Stable operation
    Lengthening of the wear ring on the body side by, 30% at maximum, helps to achieve smooth movement.
  • Lengthening of the wear ring on the body side by, 30% at maximum, helps to achieve smooth movement.

Air Slide Table/High Rigidity Type ø32 MXQ32-X2600

Updated Apr-23

  • A linear guide with a 4-row circular arc groove for high rigidity and high precision
  • Table displacement: Reduced by 50% (0.022mm→0.011mm)
  • Max. load mass: 160 N
  • Aluminum table:
    Load weight increased by reducing the weight of moving parts
  • Integrated pilot port, stroke adjuster, and auto switch on 1 side allows for improved operability

Plug-in Bottom Ported Manifold with Stainless Steel Plate JSY3000-S Series

Updated Mar-23

  • Bottom seal/stainless steel plate prevents the flooding of valves.
  • Wiring
    D-sub connector/Flat ribbon cable/Terminal block box/Lead wire/Serial unit (EX600, EX245, EX250, EX260)
  • Compatible with EtherNet/IP™ and IO-Link

Compact Type Speed Controller with Indicator JAS-SML/SCL Series

Updated Mar-23

  • Improvement of resolution has made it possible to make fine adjustment.
    1〜50mm/s:JAS-SML Series
    50〜150mm/s:JAS-SCL Series
  • Height: Max. 20.8 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes

Longer Life Cylinder CJ2-XB24

Updated Mar-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models, CJ2 Air Cylinder series

Longer Life Cylinder CQS-XB24

Updated Mar-23

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CQS Compact Cylinder series

Angle Seat Valve / Air Operated Type JSB Series

Updated Mar-23

  • Low pressure loss due to angle seat structure!
  • Long service life: 10 million cycles (Air, Water), 3 million cycles (Steam)
  • Large flow rate
    A large flow rate is possible due to the optimized flow channel shape. (Cv factor: approx. 2.5 times)
  • Compact: Height 166 mm (Port size: 1")
  • Abundant series variations of 7 sizes
  • All-in-One (Stainless steel 316L equivalent)
    Air, Water, Steam

Dual Rod Cylinder ø6, ø10, ø16, ø20, ø25, ø32 CXS2 Series

Updated Mar-23

  • Allowable kinetic energy: 0.016 J (7 times that of the existing model)
  • Max. piston speed: 800 mm/s (2.6 times that of the existing model)
  • Max. standard stroke increased
  • Mounting dimensions are compatible with the existing CXS series products.
  • Double piston construction provides twice the output force.
  • Non-rotating accuracy of ±0.1° because of the dual rod construction

Compact Type Speed Controller with Indicator JAS-S Series

Updated Mar-23

  • Height: Max. 20.8 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Mounting stud is available on the left side or the right side.

Metal Speed Controller with Indicator ASB-□H Series

Updated Mar-23

  • Improved environmental resistance with the all metal exterior [With indicator]
    For use in environment with welding spatter (Option BH type)
    Contributes to reducing setting time and errors by allowing the user to adjust flow rate before mounting and operating the cylinder
  • Possible to manage the flow rate values using an indicator!
  • Flow adjustable with a hexagon wrench tool
    Prevents accidental manual operation
  • Adjustment needle lock nut feature as standard
    Prevents unauthorized adjustment and unwanted operation of the needle from the set position due to vibrations or impacts.
    Helps improve safety in your machinery.
  • 2 types are available for different applications.
    For welding environments and for general environments

Thermo-chiller/Low-temperature Type HRS040-A-20-T1-X158/X164

Updated Mar-23

  • Supports low temperatures of as low as −10°C
  • Compact: Equivalent in size to the HRS040
  • Cooling capacity: 1 kW (At −10°C)
  • Temperature stability: ±0.1°C
  • Set temperature range: −10°C to 40°C

Speed Controller with Compact Indicator AS-FSA Series

Updated Mar-23

  • Body sizes 1/8, 1/4, 3/8, and 1/2 have been added. [New]
  • Height: Max. 5.5 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Better visibility
    Check from 360° directions is possible.
     Inspection and maintenance works are facilitated.

Speed Controller with Compact Indicator AS-FSMA/FSCA Series

Updated Mar-23

  • Body size 1/4 has been added. [New]
  • Improvement of resolution has made it possible to make fine adjustment.
    1 to 50 mm/s: AS-FSMA series
    50 to 150 mm/s: AS-FSCA series
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes
  • Better visibility
    Check from 360° directions is possible.
    Inspection and maintenance works are facilitated.

Deceleration Controller DAS Series

Updated Feb-23

  • 2-speed control reduces cycle time
    Allows for the impact relaxation of the stroke end
     Allows for the 2-speed control of cylinders
    The deceleration position (cushion timing) and 2nd speed (cushion intensity) can be adjusted.
  • Possible to control flow rate values using an adjustment handle with graduations
  • Space saving
     Maximum 76% reduction of occupying space (196cm3 ← 811cm3)

Vacuum Pad/Bowl Shape with Non-slip Feature ZP3M Series

Updated Feb-23

  • Non-slip special ribs
    Diagonal ribs are radially arranged to secure the gripping force in all directions.
    ・Prevents workpiece slippage
    ・Secure adsorbing and transferring are possible.
  • Bowl shape with excellent flexibility
    Curved workpieces can also be adsorbed.
    The pad follows the workpiece shape, making stable adsorption possible.
  • Horizontal holding force: 231 N (Pad diameter ø80)
  • Suitable for high-temperature workpieces (200°C)
  • Material: FS61 (Fluoro-based rubber) improves abrasion resistance
    ∗ More than twice the abrasion resistance of SMC's urethane pads
  • Suitable for workpieces with oil film
    As oil is ejected to the grooves between special ribs, the lateral slipping of workpiece can be suppressed even on a steel plate with oil film.

Grippers for Collaborative Robots ZXP7-PFL1-□-X1, JMHZ2-X7500-KR for KAWADA ROBOTICS CORPORATION, NEXTAGE

Updated Feb-23

    Cups with Flange

  • Standards: Conforming to ISO9409-1-50-4-M6
  • Tube-less piping
    Individual piping to suction cups is unnecessary and there is no interference with workpieces or operators
  • A wide variety of cup variations are available to support a wide range of workpieces.

  • Air Gripper

  • Compact, lightweight product with high gripping force due to air operation
  • An air gripper that realizes high rigidity and high precision due to its guide-integrated construction
  • With high-precision linear guide
  • Repeatability: ±0.01 mm
  • Standards: Conforming to ISO9409-1-50-4-M6

Air Saving Impact Blow Gun IBG Series

Updated Feb-23

  • A compact type (IBG2 series) has been added. [New]
  • Increased impact force due to higher peak pressure
  • Instantaneous air blow reduces air consumption and operation time.
  • Air consumption: 87% reduction

Vacuum Pad / Bellows Type ZP3P-JT Series

Updated Feb-23

  • A flat attachment has been added. (2.5-stage)[New]
    For reducing wrinkles
  • For the adsorption transfer of workpieces with flexible soft film packaging
  • Thin film skirt and special shaped ribs
  • The pad and attachment are made of materials compliant with FDA
    (U.S. Food and Drug Administration) regulations as well as Japan Food Sanitation Act standards.
  • Blue colored pad
    Easy to distinguish the vacuum pad by color during
    contamination inspection

Compact Guide Cylinder ø16, ø32 MGPK Series

Updated Feb-23

  • Bore sizes ø12, ø20, ø25, ø40, and ø50 have been added. [New]
  • Volume: Max. 28% reduction(538cm3→390cm3
  • Weight: Max. 41% reduction (0.32 kg a 0.19 kg)
  • High rigidity: Optimized configuration allows for compact body with high rigidity Plate thickness increased by up to 33%, Higher rigidity
  • Lube-retainer is added to the guide rod.

Vacuum Flow ZHV Series

Updated Jan-23

  • Blow and vacuum can be performed by supplying compressed air.
    Blow flow rate: Max. 6820 L/min (ANR)∗1
    Vacuum flow rate: Max. 5270 L/min (ANR)∗1
    ∗1 Values for the ZHV40 when the supply pressure is 0.5 MPa
  • It is possible to adjust the blow and vacuum flow rate by adjusting the nozzle position!
  • A vacuum flow rate 3 times or more the supply air ∗2
    ∗2 Excludes the ZHV10
  • A blow flow rate 4 times or more the supply air ∗2
    ∗2 Excludes the ZHV10
  • Weight: Max. 50% reduction (209 g ← 417 g)∗3
    ∗3 ZHV20, in comparison with product (ZH20-X185)
  • Volume: Max. 50% reduction (17000 mm3 ← 34000 mm3) ∗4
    ∗4 ZHV10, in comparison with product (ZH10-X185)
  • In terms of body mounting, port connection, and passage diameter, this product is compatible with the product (ZH-X185).

e-Actuator Easy to Operate Integrated Controller Slider Type/Rod Type EQFS□H/EQY□H Series

Updated Jan-23

  • Easy to set up, just like air equipment!
    Two position stop with no programming required
    Three position stop with no programming required
    Cycle time can be set in all control modes.
  • Downsized with Integrated Controller, Wiring saving, Labor saving
    · Programless · Reduced adjustment time
  • Annual CO2emissions reduced by up to 59% through motor control optimization 5.8 ← 14.1 [5.8 kg-CO2e/year (14.1)]
    ∗ The numerical values vary depending on the operating conditions.

Longer Life Cylinder MGJ-XB24

Updated Jan-23

  • New technology offers at least 4 times better durability.
  • Employs the same specification and mounting dimensions as the existing models,
    MGJ Miniature Guide Rod Cylinder series

Bernoulli Gripper ø20, ø30, ø40, ø60, ø80 ZNC Series

Updated Jan-23

  • Body size ø20 has been added. [New]
  • For the adsorption transfer of thin cloths, films, printed circuit boards, etc.
  • Energy saving: Max. 79% reduction
    (Comparison of air consumption to lifting force)
  • High lifting force: 65 N
    10.3 times that of the existing model
    (Existing model: 6.3 N → ZNC80: 65 N)
  • 3 types of body materials: Aluminum, Resin, Stainless steel
  • Attachment
    With stopper: Prevents workpiece slippage
    With vibration suppression cover: Suppresses the vibration noise of thin workpieces

Speed Controller with Compact Indicator AS-FSA Series

Updated Dec-22

  • Height: Max. 5.4 mm shorter
  • Flow rate can be controlled numerically with the indicator window.
    Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
    Reduces work-hours and setting mistakes

Longer Life Cylinder MGP-XB24

Updated Dec-22

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and mounting dimensions as the existing models, MGP Compact Guide Cylinder series

Water Resistant 2-Color Indicator Solid State Auto Switch/Direct Mounting Type D-M7BA□

Updated Dec-22

  • Improved water (coolant) resistance
  • Features a liquid pool-free electrical entry construction
     (The electrical entry is located on the top of the switch body.)
  • Blocks the entry of liquid from the indicator light

Dust Resistant Cylinder MXQ-XC4A

Updated Nov-22

  • Compatible with environments where powder particles of 20 to 50 μm in diameter, such as ceramic powder, toner powder, paper powder, metal powder (excluding welding spatter), etc., are present
  • 4 times more durable than the standard model
    Lube-retainers are installed on the guide unit and rod cover.
    This prevents the entry of dust and foreign matter.
  • Dimensions and workpiece mounting dimensions are interchangeable with the standard product.

Electric Actuator/Slider Type High Rigidity Guide LEKFS Series

Updated Nov-22

  • An AC servo motor type has been added. [New]
  • Size 16 has been added to the battery-less absolute type. [New]
  • Circular arc grooves allow for high rigidity and high precision.
  • Moment resistance improved by up to 61%
  • Table displacement reduced by up to 50%
  • With internal battery-less absolute encoder
    Restart from the last stop position is possible after recovery of the power supply.
    Reduced maintenance (No need to manage or replace batteries)
  • Positioning repeatability: ±0.01 mm

[Model with Residual Pressure Release Function] Pilot Check Valve/Compact Type AKP Series

Updated Oct-22

  • Model with residual pressure release function
    It is possible to construct a safety circuit!
  • Model without residual pressure release function
    Temporary intermediate stops are possible.
    ∗ Precise intermediate stops are not guaranteed.
  • Vertical and horizontal types are available, which can be selected depending on the installation conditions.
  • Improved piping design flexibility (360°-rotation type)

Direct Operated/Pilot Operated 2-Port Solenoid Valve JSX/JSX□ Series

Updated Oct-22

  • Improved environmental resistance due to the stainless steel coil cover
    [IP67 enclosure]
  • Body material: Stainless steel, Brass/Bronze, Aluminum
  • Environmental resistance: IP67 enclosure
    (IP65 for models with a DIN terminal)
  • Space saving
    Compact: Valve volume reduced by 25% (Compared with the existing model),
    Lightweight: Weight reduced by 30% (Compared with the existing model)
  • Energy saving
    Coil force: 10% increase (Compared with the existing model),
    Power consumption: 14% reduction (Compared with the existing model)
  • 360° lead wire insertion and removal is possible.
  • Flow rate increasable by up to 86% (High flow/ Power saving type)
  • Can be connected to modular type F.R.L. units (JSXM)

Clamp Cylinder ø40, ø50, ø63 CK□1 Series

Updated Oct-22

  • Weight: 7% reduction (1.96 kg → 1.82 kg)
  • 3 types of clevis widths: 12.5 mm, 16.5 mm, 19.5 mm
    Possible to select depending on the application
  • Mounting dimensions are interchangeable with the existing CK1 series model.
  • Switch mounting rod and piping port are mountable in three orientations.
  • Various types of auto switches can be mounted.
    Magnetic field resistant auto switches, Standard auto switches

Longer Life Cylinder CU-XB24

Updated Oct-22

  • New technology offers at least 4 times better durability.
     The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models, CU Free Mount Cylinder series

Battery-less Absolute Encoder Type Electric Actuator/High Performance Slider Type, High Rigidity Guide LEKFS□G Series

Updated Sep-22

  • Reduces cycle time
    Cycle time: Reduced by 39% (0.57 s ← 0.93 s) compared with the existing model
    ∗ When LEKFS25GH-400 is operated from 0 to 400 mm (stroke)
    Acceleration/Deceleration: 10000 mm/s2(334% increase compared with the existing model)
    Max. speed: 1500 mm/s (Improved by 25% compared with the existing model)
  • Circular arc grooves allow for high rigidity and high precision.
  • Moment resistance: Improved by up to 61%
  • Battery-less absolute encoder compatible
    Easy operation restart after recovery of the power supply
    Maintenance labor can be reduced as the product does not require the use of batteries.

High Performance Electric Actuators LEFS□F/LEY□F Series

Updated Sep-22

  • A rod type (LEY□F) has been added. [New]
  • LEFS□F: Reduced by 39% (0.57 s ← 0.93 s) compared with the existing model∗1
    LEY□F: Reduced by 44% (0.54 s ← 0.97 s) compared with the existing model∗2
     ∗1 When LEFS25FH-400 is operated from 0 to 400 mm (stroke)
     ∗2 When LEY25FA-300 is operated from 0 to 300 mm (stroke)
  • Acceleration/Deceleration: 10000 mm/s2
    (334% increase compared with the existing model)
  • Max. speed
    LEFS□F: 1500 mm/s (Improved by 25% compared with the existing model)
    LEY□F: 800 mm/s (Improved by 60% compared with the existing model)

Longer Life Cylinder CM2-XB24

Updated Sep-22

  • New technology offers at least 4 times better durability
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models, CM2 Air Cylinder series.

Power Clamp Cylinder CKZ5T Series

Updated Sep-22

  • A new structure has achieved downsizing.
    Overall length reduced by 49 mm max.
    Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3T in terms of installation)
  • Weight reduced by up to 23%
    Aluminum body with greatly reduced weight
  • High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
  • Manual lock release operability has been improved.
  • Spatter-proof construction
    Fully enclosed structure by means of an aluminum body

NAAMS Standards Compliant
Power Clamp Cylinder CKZ5N Series

Updated Sep-22

  • A new structure has achieved downsizing.
    Overall length reduced by 49 mm max.
    Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3N in terms of installation)
  • Weight reduced by up to 27%
    Aluminum body with greatly reduced weight
  • High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
  • Manual lock release operability has been improved.
  • Spatter-proof construction
     Fully enclosed structure by means of an aluminum body

Thermo-chiller/Standard Type (Air-cooled refrigeration) HRS400 Series

Updated Sep-22

  • Cooling capacity: 38 kW
  • Power supply: 3-phase 380 to 415 VAC (50/60 Hz)
    3-phase 460 to 480 VAC (60 Hz)
  • Set temperature range: 5 to 35°C
  • Max. ambient temperature: 45°C
  • Temperature stability: ±0.1°C
  • With heating function
  • Immersion pump (Mechanical sealless)
  • Waterproof specification: IPX4
  • Touch panel, Improved usability and visibility

Electric Actuator/High Performance Rod Type LEY□G Series

Updated Sep-22

  • Reduces cycle time
    Cycle time: Reduced by 33% (0.65 s ← 0.97 s) compared with the existing model
    Acceleration/Deceleration: 10000 mm/s2(334% increase compared with the existing model)
    Max. speed: 700 mm/s (Improved by 40% compared with the existing model)
    ∗When LEY25GA-300 is operated from 0 to 300 mm (stroke)
  • Battery-less absolute encoder compatible
    Easy operation restart after recovery of the power supply
    Maintenance labor can be reduced as the product does not require the use of batteries.

Peltier-type Chiller Thermo-con/Compact Type (Air-cooled) HEF Series

Updated Sep-22

  • Compact: 130 mm (Width) x 210 mm (Height) x 150 mm (Depth)
  • Low-noise design (at low load): 37 dB
  • Cooling capacity: 220 W
  • Temperature stability: ±0.1°C
  • Set temperature range: 10°C to 60°C
  • Superior temperature control
    Now only takes about 41 seconds to lower the temperature by 10°C 86% reduction (41 s ← 294 s) ∗ Compared with the existing product HECR002
    ∗ Time to change the circulating fluid temperature from 30°C to 20°C (when the circulating fluid IN and OUT are directly connected)

Modular Connection Type Antibacterial Filter/Odor Removal Filter/Bacteria Removal Filter HF2-BF□ Series

Updated Aug-22

  • Products Utilizing US FDA/Japan Food Sanitation Act compliant materials
  • NSF-H1 grade grease
  • Antibacterial coating
  • Designed for hygiene management in accordance with HACCP and other standards
  • Contributes to the FSSC22000 certification acquisition
  • Antibacterial filter: Antibacterial activation value: 4 or higher
  • Bacteria removal filter: Bacteria capture performance: LRV ≥ 9
  • Odor removal filter: Oil concentration on the outlet side: 0.003 mg/m3 or less

Thermo-chiller Compact Dual/Basic Type for Lasers HRLE Series

Updated Jul-22

  • A 5 kW cooling capacity specification (HRLE050) has been added. [New]
  • With functions narrowed down, 2 independent temperature control systems have been achieved with only a single compressor, a single pump, and a single tank.
  • Space saving: Footprint reduced by 21%
  • Energy saving: Power consumption reduced by 17%
  • Protection of the electrical unit: IPX4

Dust Resistant Cylinder CM2/CG1/MB/CQ2/MGP-XC4□

Updated Jul-22

  • CM2-XC4□ has been added. [New]
  • Up to 6 times more durable in dusty environments
    Applicable powder particle size: 20 to 100 μm
     Suitable for environments with ceramic powder, toner powder, paper powder, and metallic powder
    ∗ Excludes weld spatter
  • Can be selected according to the application
    A Lube-retainer (stable lubrication function) and a heavy-duty scraper can be mounted on the piston rod.
    For the MGP series compact guide cylinder, they can also be mounted on the guide rod (one or both sides).
  • The rod cover assembly can be replaced according to the operating environment.
    ∗ Only for bore sizes ø20, ø25, and ø32 of the CQ2 series

Air Cylinder ø125, ø140, ø160, ø180, ø200, ø250, ø320 CS2 Series

Updated Jun-22

  • Bore size ø320 has been added to the standard type (single rod and double rod). [New]
  • A long stroke type (ø180 to ø320) has been added. [New]
  • Lightweight: Weight reduced by up to 65% (39.1 kg → 13.4 kg)
  • High rigidity (Allowable lateral load: Max. 900 N)
  • Improved ease of piping:
     Centralized piping ports in the axial direction increase piping flexibility.
    (Axial centralized piping type)

Compact Vacuum Unit Ejector System/Vacuum Pump System ZQ□A Series

Updated Jun-22

  • Vacuum pressure switch with energy saving function
    Air consumption: 90% reduction (Based on SMC’s measurement conditions)
    Power consumption: 60% reduction [1 W (Existing model) → 0.4 W]
    Vacuum release pressure: From 0 MPa [From 0.3 MPa (Existing model) → From 0 MPa]
    Copy function: Reduced setting labor, Minimized risk of setting mistakes
  • Compatible with ejector systems and vacuum pump systems

Battery-less Absolute Encoder Type
Electric Actuator High Performance Slide Table/High Precision Type LESYH□G Series

Updated Jun-22

  • Reduces cycle time
  • Cycle time: Reduced by 39% (0.37 s ← 0.61 s) compared with the existing model
  • Acceleration/Deceleration: 10000 mm/s2
    (200% increase compared with the existing model)
  • Max. speed: 800 mm/s (Improved by 200% compared with the existing model)
  • Battery-less absolute encoder type
    Restart from the last stop position is possible after recovery of the power supply.

IO-Link Compatible
For General Fluids: 3-Screen Display High-Precision Digital Pressure Switch
ZSE20C(F)-L/ISE20C(H)-L Series

Updated Jun-22

  • IO-Link compatible
  • Stainless diaphragm: Oil-free (Single-layer diaphragm structure)
    Sensor unit: Stainless steel 630, Fitting parts: Stainless steel 304
  • Visualization of operation/equipment status/Remote monitoring and control by communication

Stainless Steel Speed Controller with One-touch Fitting ASG Series

Updated Jun-22

  • Improved environmental resistance with the all stainless steel exterior
     Possible for use in environments such as high temperature, water splashing, and where copper and zinc cannot be used
  • Max. operating temperature: 150℃
  • NSF H1 grease
  • Connection thread: Supports M5, R, and G
  • Material: Stainless steel 316 (Body A), FKM (Seal material)
    * Stainless steel 304 is used as the material for parts other than body A.
  • Compact: Height reduced by 23%, Lightweight: 21 g ← 42 g

High Speed Pilot Operated Solenoid Valve DXT1215 Series

Updated May-22

  • High speed ON: 2.5 ms, OFF: 3 ms
  • Large flow rate: 330L/min(ANR)
    * When the inlet side is 0.6 MPa, and the differential pressure is 0.1 MPa
  • Enclosure: IP67
  • Power saving: 1.5 W (With power-saving circuit)
  • Select from 3 or 5 port.
    * 3-port type: Made to order (-X1)
  • Compact
     Overall length: 91.5 mm, Width: 16 mm, Height: 34 mm

Rotary Table/Rack & Pinion Type Size:10, 20, 30, 50 MSQ Series

Updated May-22

  • An external shock absorber option has been added. [New]
  • Compact and lightweight
    Height: Max. 28% reduction∗ (54 mm → 39 mm)
    Weight: Max. 28% reduction∗ (940 g → 680 g)
  • Enlarged center hole diameter for piping (ø9 mm → ø12 mm)
    * Compared with the existing model (MSQ20)
  • The adjustable rotation time range is expanded. (0.2 to 2.0 s/90°)
    Can be used at lower speeds compared with the existing model

3-Screen Display High-Precision Digital Pressure Switch ISE7□/7□G/79S Series

Updated May-22

  • The ISE79S for general fluids (50 MPa) has been added. [New]
  • It is possible to change the settings while checking the measured value.
  • IO-Link
  • Angled display
    Good visibility from various mounting positions
  • Rotating display
    Display can rotate 336 degrees after installation.
  • Applicable fluids: Air, Non-corrosive gas, Non-flammable gas (ISE70/71)
    : Liquid or gas that will not corrode materials of parts in contact with fluid (ISE7□G/79S)

2-Layer Fluoropolymer Polyurethane Tubing TUL Series

Updated May-22

  • Flexible 2-layer tube with polyurethane outer layer
  • 2-layer construction (Outer layer: Polyurethane, Inner layer: Fluoropolymer)
  • Tubing I.D.: Cross-section ratio increased by 44% (Compared to TU0805)

Soft Start-up Valve AV□2000-A/3000-A/4000-A/5000-A Series

Updated May-22

  • An air operated type (AVA series) has been added. [New]
  • A lockout type (AVL series) has been added. [New]
  • A start-up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off the air supply
  • Power consumption: 0.35 W
  • Improved flow rate characteristics: By up to 2.3 times (C[dm3/ (s・bar) ]: 9.2)
  • Energy saving: No air flow when the main valve is switched
  • Improved low-speed air supply adjustability
  • Smaller profile and less work required due to integrated silencer

Battery-less Absolute Encoder Type
Electric Actuator High Performance High Rigidity Guide Rod Type LEG Series

Updated May-22

  • Max. weight of transferred object: 75 kg (Size 25), 100 kg (Size 32), 150 kg (Size 40)
  • High performance step motor controller
    (Max. acceleration/deceleration: 5000 mm/s2)
  • With internal battery-less absolute encoder
  • Auto switches are mountable. (In-line only)
    For checking the limit and the intermediate signal
  • Fully integrated the compact guide unit for improved lateral load capacity

Pulse Valve Valve for Dust Collector JSXF/JSXFA Series

Updated Jul-23

  • A SMARTVENT type has been added. [New]
    The integrated control board eliminates the need for a control box.
  • Life: 10 million cycles or more/10 times or more
  • High peak pressure and low air consumption
    Peak pressure: 15% increase, Air consumption: 35% reduction
  • Fluid temperature: −40 to 60°C
    Can be used in a wide range of temperatures

Vacuum Pad Flat Type with Ribs/Bellows Type ø20, ø25, ø32, ø40, ø50 ZP3C Series

Updated Apr-22

  • Suitable for the adsorption transfer of corrugated cardboard, etc., requiring abrasion resistance
  • Material: FS61 (Fluoro-based rubber) improves abrasion resistance
    ∗ More than twice the abrasion resistance of SMC’s urethane pads
  • Easier maintenance
    Compatible with 2 types of mounting tools
  • Reduced suction of foreign matter due to mesh filter
    Reduced suction of foreign matter into the vacuum pump and ejector
    The pad and mesh filter can be replaced without tools.
    The pad and mesh filter can be replaced without tools.

Step Motor Controller JXC Series

Updated Mar-22

  • A controller with STO sub-function has been added. [New]
  • Parallel I/O
  • Step motor (Servo/24 VDC)
  • Number of step data: 64 points

Longer Life Cylinder CQ2-XB24

Updated Mar-22

  • New technology offers at least 4 times better durability.
    The maintenance intervals will be extended.
  • Employs the same specification and dimensions as the existing models,
    CQ2 Compact Cylinder series

Battery-less Absolute Encoder Type
Electric Actuator/High Performance Slider Type LEFS□G Series

Updated Mar-22

  • Reduces cycle time
    Cycle time: Reduced by 39% (0.57 s ← 0.93 s) compared with the existing model
    Acceleration/Deceleration: 10000 mm/s2 (334% increase compared with the existing model)
    Max. speed: 1500 mm/s (Improved by 25% compared with the existing model)
  • Battery-less absolute encoder compatible
    Easy operation restart after recovery of the power supply
    Maintenance labor can be reduced as the product does not require the use of batteries.

Rotary Actuators CRB/CDRB Series

Updated Feb-22

  • A 270° rotating angle specification has been added. (Size: 10, 15, 40) [New]
  • Features a compact body with a built-in angle adjustment unit and
    auto switch unit (Size: 20, 30, 40)
    Overall length: 44% shorter, Weight: 48% lighter
  • Piping, wiring, and angle adjustment can be performed on the same side for easier mounting.
  • Easy-to-adjust start and end positions with the angle adjustment bolts
    (as standard)
  • The position of the chamfered portion of the shaft can be easily checked using the rotating angle indicator. (Only for the CDRB with auto switch)
  • Each of the units below for the CRB2 series can be mounted to the CRB series.

Low Air Consumption Booster Regulator (Size: 10A, 20A) VBA Series

Updated Feb-22

  • Air consumption: Max. 40% reduction
    (Based on SMC’s measuring conditions)
    Driven by reusing the exhaust air
  • Operation noise: 65 dB (A)
    15 dB (A) reduction compared with the existing model (VBA series) (Based on SMC’s measuring conditions)
  • Charging time: Max. 50% shorter
  • Operating cycles: 50 million cycles or more
    Maintenance frequency is reduced due to improved life. (Based on SMC’s test conditions)
  • Compatible with vertical and horizontal installation
  • Mounting compatibility with the existing model (VBA series)

Flame Resistant (Equivalent to UL-94 Standard V-0) Spatter Cover KR-□C-X1807

Updated Feb-22

  • Prevents the adhesion and entry of welding spatter
  • Uses a flame-retardant material
    (Equivalent to UL-94 Standard V-0 Soft PVC)

Mist Separator Regulator AWM-D Series
Micro Mist Separator Regulator AWD-D Series

Updated Feb-22

  • Transparent bowl guard
    Improved environmental durability due to 2-layer construction
    (Body sizes 30 and larger) Better visibility: 360°
  • Lightweight: Max. 40.7% reduction (0.24 kg)

High Pressure Coolant Check Valve AK-DPY00025/26

Updated Jan-22

  • Max. operating pressure: 15 MPa
  • Compact and lightweight: Weight 130 g (Rc3/8), 210 g (Rc1/2)
  • Structure that prevents foreign matter from piling up around the main
    valve Laser-welded connection prevents looseness

High Purity Air Operated Chemical Liquid Valve JLV20/30/50 Series

Updated Jan-22

  • Body class 3 has been added.[New]
  • Suppresses the generation of particles and reduced footprint!
    The special structure allows for reduced impact when the valve is closed
    as well as particle generation suppression.
    Reduced footprint (Compared to the existing model):
    Valve width reduced by 20%, Mounting pitch reduced by 45%
  • Applicable for applications requiring high pressure/high back pressure
    Operating pressure: 0 to 0.5 MPa, Back pressure: 0 to 0.5 MPa
     (Improved by 66% compared to the existing model)

Booster Regulator VBA10A/11A Series

Updated Dec-21

  • Increase factory air pressure by 4 times!
  • Air-only operation requires no power supply,
    and allows easy installation.
  • Air consumption: Max. 25% reduction (Pressure increase ratio: Twice),
    Max. 30% reduction (Pressure increase ratio: 4 times)
  • Max. flow rate: 10% increase (Pressure increase ratio: Twice),
    30% increase (Pressure increase ratio: 4 times)
  • Charging time: Max. 30% shorter (Pressure increase ratio: Twice),
    Max. 60% shorter (Pressure increase ratio: 4 times)
  • Improved service life: 50 million cycles or more
    (Pressure increase ratio: Twice, 4 times)
    Maintenance frequency is reduced due to improved life.

Plug-in Compact 5-Port Solenoid Valve JSY1000/3000/5000 Series

Updated Dec-21

  • Can be connected with the ZK2 series vacuum unit [New]
  • Size reduction has been made possible thanks to a flow increase.
    This allows for space saving, weight reduction, and a large flow rate.
  • Power consumption: 0.1 W (With power-saving circuit*), 0.4 W (Standard)
    *Made to Order
  • Connector type manifold
  • A 4-position dual 3-port valve is available.

Flat Head Screwdriver Adjustable Metal Speed Controller with One-touch Fitting  ASB-D Series

Updated Dec-21

  • Improved environmental resistance with the all metal exterior
  • Flow adjustable by a flat head screwdriver
    Prevents accidental manual operation
  • Adjustment needle lock nut feature as standard
    Prevents unauthorized adjustment and unwanted operation
    of the needle from the set position due to vibrations or impacts.
    Helps improve safety in your machinery
  • More compact: Height reduced by 28% (For G thread, face seal)
  • 2 types are available for different applications.
    For welding environments and for general environments

Low Profile Air Gripper ø8, ø12, ø16, ø20 MHF2 Series

Updated Nov-21

  • An actuator position sensor compatible type has been added. [New]
  • Height dimension reduced to approximately 1/3
  • Low profile design that reduces moment generation
  • Short, middle, and long strokes are available.
  • Compact, but the double piston mechanism provides it with a strong gripping force.

Direct Operated 3-Port Solenoid Valve V100 Series

Updated Nov-21.

  • A large flow type (Type U) has been added. [New]
  • Power consumption: 0.1 W (Standard type, With power-saving circuit)
  • Coil temperature rise: 1°C (Standard type, With power-saving circuit)

Non Plug-in Body Ported Single Unit (For Mounting P.E Plate)/JSY1000/3000/5000 Series

Updated Oct-21

  • A body ported type (single unit) has been added.

Pinch Valve LPV Series

Updated Oct-21

  • Highly resistant to contamination and reduces valve failures
  • Applicable tubing:
    Silicone, PharMed®BPT, Tygon®
  • Power consumption: 2.0 W
  • Compact: Valve width 20 mm
  • Easy tubing replacement

Separate Controller Ionizer Bar Type/Nozzle Type IZT40/41/42/43 Series

Updated Oct-21

  • An IO-Link type has been added to the IZT41/42/43.[New]
  • The controller and high-voltage power supply module can be mounted separately.
  • Space saving: Height 37 mm x Width 30 mm (Bar type)
    Thickness 16 mm x Width 53 mm x Height 32 mm (Nozzle type)
  • One controller can control a maximum of 4 ionizers.
  • Potential amplitude: 25 V or less
  • Rapid static neutralization: Fastest time of 0.1 s
  • 3 types of emitter cartridges
    High speed static neutralization cartridge
    Energy saving static neutralization cartridge
    Energy saving high-efficiency cartridge
  • Static neutralization is possible even when air is not being supplied.

3-Color Display Digital Flow Switch PF2MC7(-L) Series

Updated Oct-21

  • Dry air, N2
  • 3-color/3-screen display
  • A wide range of flow measurement is possible with 1 product.
    Flow ratio 100:1, Smallest settable increment: 1 L/min
  • Grease-free
  • IO-Link compatible

Modular Connection Type 5-Port Solenoid Valve SY3000/5000-X990

Updated Sep-21

  • Can be connected to F.R.L. units (AC-D series)
  • Allows for space saving and reduced piping labor
  • Flow rate characteristics C [dm3/(s·bar)]
    SY3000: 1.6, SY5000: 3.6

Air Gripper Unit for Collaborative Robots JMHZ2-X7500-KA
for the Kawasaki Heavy Industries, Ltd. duAro 1, 2 Series

Updated Aug-21

  • Compact, lightweight product with high gripping force due to air operation
  • An air gripper that realizes high rigidity and high precision due to its guide-integrated construction
    With high-precision linear guide, Repeatability: ±0.01 mm
    Linear guide of the higher rigidity and precision is used. Higher rigidity
  • Integrated speed adjustment mechanism
  • A split protective cover for easy air gripper maintenance
  • Selectable attachment, protective cover, and number of auto switches

High Pressure Coolant Valve SGH Series

Updated Aug-21

  • Max. operating pressure: 3 MPa, 7 MPa, 10 MPa [New]、14MPa [New]
  • Applicable to high-speed grinding and long drilling processes
  • Coolant valve for high-pressure coolant liquid that is ideal for lubrication, dust blowing, and cooling
  • Service life: 3 million cycles (Based on SMC’s test conditions)
  • Water hammer: Reduced by 20% (Compared to existing model, VNH series)
  • Power consumption: 0.35 W (24 VDC, V116)
  • The 3-port dual pressure type has been standardized.

Vacuum Manifold for Fieldbus System ZKJ Series

Updated Aug-21

  • Fieldbus-compatible
    Requires no input/output unit. Space saving
    Reduced wiring time
    Compatible protocol: PROFINET, IO-Link
  • Energy saving ejector: Air consumption reduced by 90%
  • Supply valve: N.O. specification
    Can hold vacuum even when the power goes out or is turned off (Supposing the supply pressure is being maintained)
    Prevents the sudden dropping of workpieces (Supposing the supply pressure is being maintained)
  • IP65: Dust-tight/Water-jet-proof

Vacuum Gripper for Collaborative Robots ZXP7□-X1□-KA
for the Kawasaki Heavy Industries, Ltd. duAro 1, 2 Series

Updated Aug-21

  • A compact, lightweight all-in-one vacuum gripper
  • Integrated vacuum ejector, air supply/release valve, pressure switch, and cups
  • Integrated vacuum ejector, pressure switch, and cups
  • Standards: Conforming to ISO 9409-1-31.5-4-M5
  • A wide variety of cup variations are available to support a wide range of workpieces.

Pin Cylinder: Single Acting, Spring Return ø4, ø6, ø10, ø16 CJP Series

Updated Aug-21

  • A short-stroke miniature cylinder with a shorter overall length
  • Rod end cap can now be ordered with the cylinder.
  • One-touch fitting can be connected. (Panel mount type)
  • 16 mm bore size is now available. (Existing product: 15 mm)

Air Cylinder ø20, ø25, ø32, ø40 CM2 Series

Updated Aug-21

  • Cylinder with rod end bracket is standardized.
  • Interchangeable in mounting with the existing model
  • Various mounting bracket options
    Mounting brackets suitable for various installation conditions
    Improved mounting flexibility
  • Part numbers for products with a rod end bracket and/or a pivot bracket available
    It is not necessary to order a bracket for the applicable cylinder separately.
  • Easy fine adjustment of auto switch position
  • Overall length is shortened with boss-cut type.
  • With auto switch (CDM2-Z1)

2-Color Display
Digital Flow Switch PF2M7(-L) Series

Updated Jul-21

  • A 2 to 200 L/min flow range option has been added. [New]
  • A rear ported type has been added. [New]
  • A flow adjustment valve (0.05 to 5 L/min)
    has been added. [New]
  • Dry air, N2, Ar, CO2
  • A wide range of flow measurement is possible with 1 product.
    Flow ratio 100:1, Smallest settable increment: 0.01 L/min
  • IO-Link compatible
  • Improved resistance to moisture and foreign matter
  • Compact, Lightweight
  • Grease-free

One-touch Fitting with Improved Weather Resistance KQ-X1744

Updated Jul-21

  • Improved weather resistance in outdoor environments
  • Accelerated weathering test: Passed 1000 hours
    ISO 4892-3 (JIS K 7350-3) compliant
  • Combined cycle test: Passed 960 hours
    ISO 14993 (JIS H 8502: 1999) compliant
  • Ozone-proof exposure test: Passed 1000 hours
    ISO 1431 (JIS K 6259) compliant

Exhaust Flow Control Valve with Indicator AS-DPX00042

Updated Jul-21

  • Contributes to reduced setting errors and work
    hours by managing flow rate figures (indicator)
  • Integrated restrictor and silencer
    Reduced assembly time and number of components
  • The speed can be adjusted on the valve side

Electric Actuator
Slide Table/High Precision Type LESYH Series

Updated Jul-21

  • Improved positioning repeatability due to the adoption of a ball screw drive.
    Positioning repeatability: ±0.01 mm
  • Lost motion: 0.1 mm or less
  • Increased vertical work load: 5 times or more
  • Motorless type
    Can be used with your current motor and driver !

Electric Actuator Battery-less Absolute Encoder Type LEF□16E/LEY16E Series

Updated Jul-21

  • Restart from the last stop position is possible after recovery of the power supply.
  • Easy operation restart after recovery of the power supply
  • Does not require the use of batteries. Reduced maintenance
    Batteries are not required to store the position information. Therefore, there is no need to store spare batteries or to recycle and replace dead batteries.
  • Size 16 has been added. [New]
    Slider Type LEF, Rod Type LEY(G)

3-Color Display Digital Flow Switch for Large Flow PF3A□H(-L) Series

Updated Jul-21

  • A 4-screen display digital flow switch with pressure/temperature sensor(modular type) has been added.[New]
  • Applicable fluid: Air, N2
  • Flow ratio 100:1
    A wide range of flow measurement is possible with 1 product.
  • Improved resistance to moisture and foreign matter
  • IO-Link compatible

Electric Actuator Rod Type LEY100 Series

Updated Jul-21

  • Max. force: 12000 N, Work load: 1200 kg, Max. stroke: 1000 mm
  • Can be mounted in accordance with ISO 15552
  • Modify the force/speed specifications
    (Change specifications by changing or removing the reducer)
  • Motorless type
  • An auto switch can be mounted

Electro-Pneumatic Regulator/Electronic Vacuum Regulator ITV Series

Updated Jun-21

  • IO-Link compatible products have been added.
    IO-Link communication enables users to check device information
    and monitor device status in addition to performing pressure control.

OSHA Standard Compliant Pressure Relief 3-Port Valve with Locking Holes 
VHS□-D/VHS□W-D Series

Updated Jun-21

  • Improved flow rate characteristics: Max. 88% increase (VHS40-04-D)
  • Energy saving: Zero blow-by of the air during switching of the handle
  • OSHA (Occupational Safety and Health Administration) standard compliant
  • Safety measure: Can prevent accidents caused by inadvertent
    air supply problems With the indicator window, Double action
  • Lower pressure drop contributing to energy saving
    Pressure drop: reduced by up to 73%

Air Cylinder ø20, ø25, ø32, ø40 JCM Series

Updated Jun-21

  • A foot type and a flange type have been added.[New]
  • Overall length shortened by up to 97 mm
  • Weight: Max. 54% lighter (0.69 kg→0.32 kg)
  • Various cover types available
  • Port size: M5, Rc1/8, and NPT1/8 available
  • Male and female rod ends available
  • With auto switch (JCDM series: JCDM)

Compact Type Parallel Style Air Gripper JMHZ2 Seriess

Updated Jun-21

  • A single acting type has been added.[New]
  • Made-to-order options have been added:[New]
    With positioning pins on the lateral mounting surface, Lateral auto switch mounting
  • Downsizing is possible without changes to the gripping point range. (ø20→ø16)
    Overall length: Max. 21.7 mm shorter (102.7 mm→81 mm)
    Thickness: Max. 7.6 mm shorter (33.6 mm→26 mm)
    Weight: Max. 180 g lighter (420 g→240 g)
  • High rigidity and precision are achieved by integrating the guide and finger.

Compact Cylinder ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100  JCQ Series

Updated Jun-21

  • An axial foot type and a flange type have been added. (ø32 to ø100)[New]
  • Compact: Overall length shortened by 6.5 mm, Width shortened by 6 mm, Height shortened by 4 mm
  • Weight: Max. 46% lighter (382 g → 204 g)
  • Volume: Max. 40% reduction
  • With auto switch (JCDQ Series: JCDQ)

Clean Design Manifold Valve JSY5000-H Series

Updated Jun-21

  • Low fluid accumulation, Easy to clean
  • Large flow rate: 1,600 L/min (ANR)
  • Enclosure: IP69K
  • NSF-H1 grease
  • External parts: FDA-compliant materials
    (Metal parts are made of stainless steel 316 with high anti-corrosion performance.)
  • Wiring: Lead wire/Fieldbus type (IO-Link)

Air Cylinder ø32, ø40, ø45 , ø50, ø56 , ø63, ø67 , ø80, ø85 , ø100 JMB Series

Updated Jun-21

  • A both ends tapped mounting option has been added.[New]
  • Intermediary bore sizes: ø45, ø56, ø67, ø85
    Air saving, Space saving
  • Overall length shortened by 27 mm
  • Weight reduced by up to 36% (1.56 kg → 1.00 kg)
  • Air saving: Reduced by up to 29%
    Air consumption can be reduced by optimal size selection.

3-Port Solenoid Valve Modular Type/Residual Pressure Release Valve VP546E/746E Series

Updated Jun-21

  • Can be connected to F.R.L. units (AC-D series)
    Allows for space saving and reduced piping labor.
  • Flow rate characteristics C[dm3(/ s·bar)]
    VP546E:7.5
    VP746E:12.6
  • A model with a soft start-up function is also available.
  • Power consumption: 0.35 W (Without light)
  • Features a check valve built into the pilot flow path
    (Supports pilot pressure drops caused by pressure fluctuations on the inlet side)

Magnet Gripper for Collaborative Robots MHM-X7400A for UNIVERSAL ROBOTS

Updated May-21

    URCap: Easy programming
  • Attracts and holds heavy objects with a magnet
  • Supports workpieces with holes and uneven surfaces
  • Compact with high holding force
    Holding force: Max. 200 N (o25, Workpiece thickness 6 mm)
  • Continues to hold workpieces even when the air is shut off
  • Operate by simply connecting 1 air supply tube and an electrical wiring M8 connector.
  • Integrated solenoid valve, auto switch, and piston speed adjustment mechanism

Magnet Gripper for Collaborative Robots MHM-X7400A-HC10/HC10DT
for the YASKAWA Electric Corporation MOTOMAN-HC

Updated May-21

  • Attracts and holds heavy objects with a magnet
  • Supports workpieces with holes and uneven surfaces
  • Compact with high holding force
    Holding force: Max. 200 N (ø25, Workpiece thickness 6 mm)
  • Continues to hold workpieces even when the air is shut off
  • Operate by simply connecting 1 air supply tube and an electrical wiring M12connector.
  • Integrated solenoid valve, auto switch, and piston speed adjustment mechanism

Magnet Gripper for Collaborative Robots MHM-X7400A-CRX
for the FANUC CORPORATION CRX Series

Updated May-21

  • Plug and Play configuration for immediate use
  • FANUC CRX plug-in software
  • Attracts and holds heavy objects with a magnet
  • Supports workpieces with holes and uneven surfaces
  • Compact with high holding force
    Holding force: Max. 200 N (ø25, Workpiece thickness 6 mm)
  • Continues to hold workpieces even when the air is shut off
  • Operate by simply connecting 1 air supply tube and an electrical wiring M8connector.
  • Integrated solenoid valve, auto switch, and piston speed adjustment mechanism

Magnet Gripper for Collaborative Robots MHM-X7400A-ASSISTA
for the Mitsubishi Electric Corporation MELFA ASSISTA Series

Updated May-21

  • Attracts and holds heavy objects with a magnet
  • Supports workpieces with holes and uneven surfaces
  • Compact with high holding force
    Holding force: Max. 200 N (ø25, Workpiece thickness 6 mm)
  • Continues to hold workpieces even when the air is shut off
  • Operate by simply connecting 1 air supply tube and an electrical wiring M12connector.
  • Integrated solenoid valve, auto switch, and piston speed adjustment mechanism

Magnet Gripper for Collaborative Robots MHM-X7400A-TM
for the OMRON Corporation and TECHMAN ROBOT Inc. TM Series

Updated May-21

  • Plug and Play configuration for immediate use
    TMComponent: Easy programming
  • Attracts and holds heavy objects with a magnet
  • Supports workpieces with holes and uneven surfaces
  • Compact with high holding force
    Holding force: Max. 200 N (o25, Workpiece thickness 6 mm)
  • Continues to hold workpieces even when the air is shut off
  • Operate by simply connecting 1 air supply tube and an electrical wiring M8connector.
  • Integrated solenoid valve, auto switch, and piston speed adjustment mechanism

Air Gripper Unit for Collaborative Robots JMHZ2-X7400B-CRX
for the FANUC CORPORATION CRX Series

Updated May-21

  • Plug and Play configuration for immediate use
  • FANUC CRX plug-in software: Easy programming
  • Compact, lightweight product with high gripping force due to air operation
  • High rigidity and high precision due to its guide-integrated construction
    Repeatability: ±0.01 mm due to the adoption of a high-precision linear guide
    Higher rigidity due to the adoption of a linear guide of the higher rigidity and precision
  • Operate by simply connecting 1 air supply tube and an electrical
    wiring M8 connector.
  • Integrated solenoid valve, speed adjustment mechanism, and auto switch
  • A split protective cover for easy air gripper maintenance

Dust-tight/Water-jet-proof (IP65 Equivalent/IP67 Equivalent) Battery-less Absolute Encoder Type Electric Actuator/Rod Type LEY-X8 Series

Updated May-21

  • Enclosure: IP65* equivalent/IP67 equivalent
    * Testing of IP65 has also been carried out.
  • Battery-less absolute encoder compatible

Actuator Position Sensor D-MP□ Series

Updated May-21

  • Now with a greater number of models![New]
    CQS Series Compact Cylinder
    MXH Series Compact Slide
    MXS and MXQm Series Air Slide Tables
    MHZ, MHZL2, MHL2, and MHF2 Series Parallel Type Air Grippers

Arc Welding Spatter-resistant Lead Wire Type Magnetic Field-resistant Solid State Auto Switch D-P3DWA□-1173□

Updated May-21

  • Improved lead wire spatter resistance
    Special fluorine compounds are used for the sheath, insulation, and insulator.
    A shield is provided between the sheath and the insulation to prevent spatter from entering the insulation.
    A type with a spatter cover is available.
  • The metal cover (Material: Stainless steel) covers the body to prevent spatter adhesion.

Vacuum Gripper for Collaborative Robots ZXP7□-X1□-ASSISTA
for Mitsubishi Electric Corporation MELFA ASSISTA

Updated May-21

  • Operate by simply connecting 1 compressed air supply tube and an electrical wiring M12 connector.
  • Integrated vacuum ejector, air supply valve, pressure switch, and cups
  • Features a rounded appearance without corners
  • A wide variety of cup variations are available to support a wide range of workpieces.

Vacuum Gripper for Collaborative Robots
ZXP7□11-X1□ for YASKAWA Electric Corporation collaborative robot MOTOMAN-HC10DT

Updated May-21

  • Can be operated simply by connecting 1 compressed air supply tube and the built-in cable for electric wiring
  • Integrated vacuum ejector, air supply/release valve, pressure switch, and cups
  • As the air piping and electric wiring built into the robot are used, no external wiring or piping is required. No interference with workpieces or workers
  • Features a rounded appearance without corners
  • A wide variety of cup variations are available to support a wide range of workpieces.

Fieldbus Syste(Output device for driving 5-port solenoid valves) EX260 Series

Updated May-21

  • A functional safety standard compliant product has been added.
  • Compact design for space-saving installation: Approx. 28 mm
  • PROFIsafe compatible
  • IO-Link compatible
  • IP67
  • Drives up to 32 solenoids
  • Daisy-chain wiring communication

For Food Industry EHEDG Compliant/Clean Design/FDA Compliant Fittings
KFG2H-E/KFG2H-C/KQG2-F/KQB2-F/KFG2-F Series

Updated Apr-21

  • Hygienic design prevents liquid from accumulating after cleaning
  • FDA compliant materials

Circulating Fluid Temperature Controller EU F-Gas Regulation-compliant Refrigerated Thermo-chiller HRZ-F Series

Updated Apr-21

  • More effective energy-saving is achieved through use of a DC
    inverter compressor and an inverter pump.
  • Energy saving
    The inverter controls the number of motor rotations of the
    compressor and pump according to the load from the user’s
    application.
    Power consumption: Max. 65% reduction
    Facility water: Max. 67% reduction
  • High performance
    Temperature stability: ±0.1°C (When a load is stable)
    Cooling time: Max. 46% reduction (SMC comparison)
  • Refrigerant: R410A (HFC)/R448A (HFC/HFO)

Process Pump Automatically Operated Type/Air Operated Type PA5000 Series

Updated Apr-21

  • Now with compact / energy saving / high-dispense-volume body material
    polypropylene (PP)!
  • Compact: Height 185 mm x Width 134 mm x Depth 202 mm
  • Lightweight: 3.0 kg (Polypropylene)
  • Fluid contact body material:
    Selectable from PP (polypropylene), aluminum or stainless steel
  • Automatically operated type and air operated type are available.
  • Self-priming makes priming unnecessary

Vacuum Gripper for Collaborative Robots for the FANUC CORPORATION CRX Series ZXP7□21-X1

Updated Apr-21

  • Plug and Play configuration for immediate use
  • FANUC CRX plug-in software
  • Operate by simply connecting 1 compressed air supply tube and an electrical wiring M8 connector.
  • Integrated vacuum ejector, air supply/release valve, pressure sensor, and cups
  • Standards: Conforming to ISO 9409-1-50-4-M6

Fieldbus System(For Input/Output) EX245 Series

Updated Mar-21.

  • PROFIsafe compatible product
  • For Input/Output
  • Push Pull connectors
    AIDA specifications compliant
    SCRJ connectors, RJ45 connectors
  • Compatible with the PROFIenergy energy-saving function
  • Shared Device function

Cylinder with Lock: With Lock Status Indication ø32, ø40, ø50, ø63, ø80, ø100 C96N-X3030□

Updated Mar-21

  • Safety measure: Whether the cylinder is in a locked or manual lock released state can be visually confirmed at a glance.
    Highly visible lock released state indication label (Yellow)
  • Available with a cap nut

Fieldbus System(For Input/Output) EX600 Series

Updated Mar-21

  • IO-Link unit compatible SI unit: EtherNet/IP™, EtherCAT [New]
  • Up to 9 IO-Link units can be connected. (36 IO-Link devices can be connected.)
    Digital units, analog units, and IO-Link units can be mixed, and up to 9 units can be connected in any order.
  • PROFINET (EX600-SPN3/4), EtherNet/IP™ (EX600-SEN3/4/7/8),
    and EtherCAT (EX600-SEC3/4) support the following functions.
  • For input/output
  • Supports digital inputs/outputs, analog inputs/outputs, and IO-Link units
  • Self-diagnosis function
  • Web server function
  • Various connectors available
  • Up to 9 units can be connected. (Excludes SI units)

ISO Cylinder/Air Cylinder Non-adjustable Air Cushion Type C85-X3242/C75-X3242

Updated Mar-21

  • Smooth stopping with less impact compared to the type that only has a rubber bumper
  • Reduced impact noise
  • No need to adjust the cushion needle
  • Shorter cycle time
    The air cushion + rubber bumper construction enables the cycle time to be shortened, compared to the type that only has an air cushion.

AC Servo Motor Driver Network Card Type LECSN-T Series

Updated Mar-21

  • Supports 3 types of network card (PROFINET, EtherCAT, and EtherNet/IP™)
  • STO (Safe Torque Off) safety function available
  • Control encoder: Absolute 22-bit encoder (Resolution: 4194304 p/rev)

External Input Signal (Remote) Type Smart Positioner IP8101-X419-□

  • Allows for the remote control of cylinders Controls the cylinder by feedback signal

Modular Type Common Supply Regulator AR□M(K)-D Series

Updated Mar-21

  • A right angle square type pressure gauge has been added.[New]
  • Supply different pressure for multiple applications
    OUT port is on the back of the product.
  • Reduced piping labor and space-saving design
  • Branch piping

Peltier-Type Chiller Thermo-con/Compact Type, Air-cooled INR-244-831

Updated Mar-21

  • Compact, Space saving
  • Refrigerant-free
  • Low-noise design: 45 dBA (When selecting an option)
  • Cooling capacity: 220 W
  • Temperature stability: ±0.01 to 0.03℃
  • Set temperature range: 10℃ to 60℃
  • Fluid contact material: Stainless steel, Resin (Aluminum and copper material-free)

End Power Cylinder ø40, ø50 CDQ2A-X3260

Updated Feb-21

  • Air consumption: Max. 73% reduction
  • Output is generated from 5 mm in front of the stroke end.
    (Extending operation only)
    Energy saving can be achieved by using the assist cylinder to
    reach the output stroke position.
  • Smooth operation even when output is generated
  • The CQ2 series rod flange type is mountable.
  • Optimal for applications such as press fitting and clamping that
    require force at the stroke end
  • Controllable by a single solenoid valve in the same way as a
    conventional cylinder

Flame Resistant (Equivalent to UL-94 Standard V-0) FR 2-Layer Soft Polyurethane Tubing TRBU-X259

Updated Feb-21

  • Peeling of the outer layer not required to connect fittings
    Reduced labor time, Improved workability
  • Improved flexibility (Compared with the TRBU)
  • Lightweight and compact
    Weight: 57% reduction, Cross sectional area: 37% reduction (Compared with the TRBU0805)
  • Suitable for air and water piping in environments where spot welding spatter may be a problem
  • Increased flow rate due to I.D. expansion: Max. 69% improvement (Comparison between the TRBU1208 and the TRBU1210-X259)

Body Ported Type/Box Type (Built-in Silencer) ZH Series

Updated Feb-21

  • Nozzle sizes: ø1.5, ø1.8, and ø2.0 have been added to the box type.[New]
  • Compact and lightweight
    Overall length: Max. 11% reduction
    Port height: Max. 25% reduction
    Volume: Max. 39% reduction
  • 4 mounting types
  • A silencer and standard bracket are available. (Body ported type only)

Air Cylinder ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 CG1 Series

Updated Jan-21

  • Improved piping flexibility
  • Cylinder with rod end bracket is standardized.
  • Interchangeable in mounting with the existing model
  • Various mounting bracket options
  • Part numbers for products with a rod end bracket and/or a pivot bracket
    It is not necessary to order a bracket for the applicable cylinder separately.

3-Color Display Digital Flow Switch PFMC7□(-L)Series

Updated Jan-21

  • IO-Link compatible [New]
  • Applicable fluid: Dry air, N2
  • 3-color/2-screen display
  • Expanded flow range
    A wide range of flow measurement is possible with 1 product.

Vacuum Gripper for Collaborative Robots ZXP7□41-X1

Updated Jan-21

  • Plug and Play configuration for immediate use
    TMComponent Easy programming
  • Operate by simply connecting 1 air supply tube and
    two electrical wiring M8 connectors.
  • Integrated vacuum ejector, air supply/release valve, pressure sensor, and cups
  • Standards: Conforming to ISO9409-1-50-4-M6

Metal Speed Controller with One-touch Fitting ASB Series

Updated Jan-21

  • Improved environmental resistance with the all metal exterior
  • For use in environments with welding spatter, dust, ultraviolet, etc.
  • Improved installability
    More space beneath the tube. Easier installation/removal of the
    tube
  • Lightweight: Approx. 28% reduction (54g → 39g)

Go Top