New Products List ｜SMC CORPORATION

Air Servo Cylinder　IN-777

New

Updated Jul-25

Produced upon receipt of order

Capable of air cylinder multipoint positioning and control
Fast response and high positioning repeatability
Positioning repeatability: ±0.5 mm
Easier maintenance due to unitization
Built-in self-diagnosis function (LED lamp and signal output)
Emergency stop of the piston when the air or power supply is cut
Supports 4-20 mA/HART communication as the communication protocol
FOUNDATION Fieldbus communication has been added as a communication protocol. [New]

NAAMS Standards Compliant
Power Clamp Cylinder　CKZ5N Series

New

Updated Jul-25

Bore sizes ø80 has been added. [New]
A new structure has achieved downsizing.
Overall length reduced by 49 mm max.
Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3N in terms of installation)
Weight reduced by up to 27%
Aluminum body with greatly reduced weight
High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
Manual lock release operability has been improved.
Spatter-proof construction
　Fully enclosed structure by means of an aluminum body

Power Clamp Cylinder　CKZ5T Series

New

Updated Jul-25

Bore sizes ø40 and ø80 have been added. [New]
Weight reduced by up to 23%
Aluminum body with greatly reduced weight
A new structure has achieved downsizing.
Overall length reduced by 49 mm max.
Depth reduced by 17.3 mm max. (Interchangeable with existing product CKZ3T in terms of installation)
Weight reduced by up to 23%
Aluminum body with greatly reduced weight
High clamping force 4000 N (ø63, Arm length: 100 mm, 0.5 MPa)
Manual lock release operability has been improved.
Spatter-proof construction
Fully enclosed structure by means of an aluminum body

Refrigerated Air Dryer/For Use in North, Central and South America　IDFB□E Series

New

Updated Jul-25

Low GWP Refrigerant [New]
UL, CSA certified product
Power supply voltage: Single-phase 115 VAC (60 Hz), 230 VAC (60 Hz)
3-phase 460 VAC (60 Hz)
Note) The air flow capacity for each dew point is indicated.

∗ The IDFB22E/37E series has been discontinued in August 2019.
　Please select the IDFB60/70 series.

Refrigerated Air Dryer/For Use in North, Central and South America　IDFB Series

New

Updated Jul-25

Low GWP Refrigerant [New]
Applicable for the high-temperature environments
Ambient temperature: Max. 113°F (45°C)
Inlet air temperature: Max. 149°F (65°C)
Increased air flow capacity
Power supply voltage: Single-phase 230 VAC (60 Hz)

Stainless Steel Cylinder　CM5□ Series

New

Updated Jun-25

External parts made of stainless steel
Stainless steel is used for the cylinder body, mounting bracket, mounting bolt, and accessories.
Compact and lightweight (Compact type)
Overall length reduced by 21%* (175 mm→139 mm)
Weight: Max. 50% reduction* (0.75 kg→0.38 kg)
∗ Compared with the existing CG5-S series at 32 mm bore and 50 mm stroke
4 times or more life expectancy under the water droplet scattering environment*
(Improved water-resistant type)
∗ Compared to the standard CM2 product series
Grease for use in food machinery: NSF-H1 certified greases are available.
Seal material: FKM or NBR are available.

Remote Control Valve (Electric speed controller)　PFES Series

New

Updated Jun-25

The speed controller is equipped with a motor
Speed controller capable of “remote control” by “electrification”
Large reduction in equipment setup time and downtime
Easy maintenance
Reduced adjustable work-hours
Improved productivity
Reduced down time

ISO 13849-1 Certified Safe Exhaust Valve Modular Connection Type　VPX400 Series

New

Updated Jun-25

Double common specification has been added. [New]
Safety standard ISO 13849-1 compliant
(Corresponding to categories 3 and 4)
Exhaust flow rate characteristics [L/min (ANR)]　∗ At 0.6 MPa
10,500 (VPX406-A3)
13,000 (VPX406-A3)
15,000 (VPX406-A6)
Space saving & lightweight: 3 functions have been integrated.
Dual residual pressure release valve + Soft start-up valve + Main valve inconsistency detection
Modular connection is possible.
(AC30/40/50/60-D series)

Pulse Blow Unit　PU Series

New

Updated Jun-25

Intermittent pulse blow improves removal efficiency by 35% compared with continuous blow. (∗ Based on the test by SMC.)
CO₂ emissions (Air consumption): 50% reduction
Possible to adjust operating frequency
External power supply is unnecessary.
A pulse blow is possible by the air supply.
Low pressure loss is achieved.
A large effective area (10.3 mm²) helps reduce the air consumption.
Possible to use it with its bracket mounted
Combined use with a blow gun
Compact, Lightweight
Weight：47 g
Valve volume：59.4 mm×24mm×28mm

Modular Type Relief Valve　AP20-D Series

New

Updated Jun-25

Releases pressure over the set range into the atmosphere and constantly maintains the pressure in a pipe
Set pressure: 0.05 to 0.8 MPa
Modular connection is possible.
Reduced piping labor, Branch piping is not required.
Easy to handle
Selection of pressure gauges

Flow Controller for Water　FC3W Series

New

Updated Jun-25

IO-Link compatible [New]
Rated control flow rate range:
A 5 to 40 (L/min) specification has been added. [New]
For the stepless control of water flow rate in proportion to electrical signals
Flow rate control accuracy: ±5% F.S.
Response time: 10 s or less
Parts in contact with fluid: Grease-free

Suction Cup/With Non-slip Feature　ZP3M Series

New

Updated Jun-25

An oval bellows shape with non-slip feature has been added. [New]
Longer life (More than twice that of urethane cups)
Cup material: FS61 (Fluoro-based rubber) with excellent abrasion resistance
Reduced number of cup replacements
Non-slip special ribs
Diagonal ribs are radially arranged to secure the gripping force in all directions.
・Prevents workpiece slippage
・Secure adsorbing and transferring are possible.
Bowl shape with excellent flexibility
Curved workpieces can also be adsorbed.
The cup follows the workpiece shape, making stable adsorption possible.
Horizontal holding force: 387 N (Cup diameter ø100)
Suitable for high-temperature workpieces (200°C)
Suitable for workpieces with oil film
As oil is ejected to the grooves between special ribs, the lateral slipping of workpiece can be suppressed even on a steel plate with oil film.

Hygienic Design Cylinder　HYB/HDYB Series

New

Updated Jun-25

A water resistant cylinder configured for easy cleaning
Approx. 5 times increase in service life compared to the existing model (SMC ratio)
Grease for food processing equipment (NSF-H1 certified) is available.
External seal material: Choice of NBR or FKM

Air Cylinder Short Type　CG3/CDG3 Series

New

Updated Jun-25

Overall length Max. 51 mm shorter, Weight Max. 24% lighter (Comparison to CG1)
With auto switch (CDG3 series: CDG3)

Air Cylinder　CG1 Series

New

Updated Jun-25

A single acting type/A direct mount type/An end lock type has been added. [New]
Improved piping flexibility
Cylinder with rod end bracket is standardized.
Interchangeable in mounting with the existing model
Various mounting bracket options
Part numbers for products with a rod end bracket and/or a pivot bracket
It is not necessary to order a bracket for the applicable cylinder separately.

Mounting Kit for Multi-Axis System　LEA Series

New

Updated Jun-25

Creation of an XYZ unit
Easy system construction using the model selection software
Compatible actuators
X-Y-axis: LEFS series, LEFB series, LEKFS series
Z-axis: LEYG series
Compatible controllers/drivers (For single axis)

JXC51/61 series, JXC91/E1/P1/D1/L1/M1 series, LECS□‐T/LECY□ series

Exhaust Flow Control Valve with Silencer　ASN2□-A Series

New

Updated Jun-25

Integrated restrictor and silencer
Reduced assembly time and number of components
Push-lock type
Resin body: Weight reduced by up to 80%
The speed can be adjusted on the valve side.
A type with a compact indicator is available.
The flow rate can be controlled numerically.
Contributes to reduced setting errors and work hours by managing flow rate figures (indicator)

Digital Flow Switch for Large Flow　PF3A□H(-L) Series

New

Updated Jun-25

Applicable fluid: Air, N₂, Ar, CO₂ [New]
500 L/4000 L/8000 L types have been added to the modular type. [New]
The display range has been expanded. (1.5 times the rated flow range) [New]
Accumulated pulse conversion value: Select from 4 types based on the flow range [New]
Accumulated pulse width: Select a setting between 50 to 100 ms [New]
A wide range of flow measurement is possible with 1 product.
Supports the IO-Link communication protocol

Membrane Nitrogen Generator　IN778-1/IN778-2

Updated May-25

Nitrogen enriched air purification is easily possible with only a compressed air supply.
Nitrogen concentration: Max. 99.9 or more/ Outlet air flow rate: 20 L/min (ANR) ^∗
∗ Inlet air pressure: 0.7 MPa, Inlet air temperature 25°C
Compact and easy to use at point of use
No power supply required
No need for gas cylinder replacement
Modular connection type
Outlet side compressed air purity class (Humidity)"2" ^∗
∗ IFor IN778-1

Refrigerated Air Dryer/For Use in Europe, Asia and Oceania　IDFA□ Series

Updated May-25

Standard IDFA□E/□ Series
・IDFA3E～15E1
　　[For use in Europe] Low GWP refrigerant: R1234yf (HFO)
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R134a (HFC)
・IDFA60 to 90
　　[For use in Europe] Low GWP Refrigerant: R454C (HFC) [New]
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R410A (HFC)
Large Size IDFA□F Series
　　[For use in Europe] Low GWP Refrigerant: R454C (HFC) [New]
　　∗ Not available for air transport
　　[For use in Asia and Oceania] Refrigerant: R407C (HFC)
・Tolerant of high temperature environment !
　　Top of its class in the industry for the large air-cooled type
　　Ambient temperature 45°C at max.,
　　Inlet air temperature 60°C at max.
・Energy saving design
　　Exhaust heat reduced by 25% at max.
　　Ambient temperature increase suppressed
　　Employs a heat exchanger made of high corrosion-resistant
　　stainless steel

In-line Air Filter　ZFD Series

Updated Apr-25

Operating pressure range: −100 kPa to 0.5 MPa
Able to capture foreign matter in both vacuum adsorption and vacuum release directions.
Prevents foreign matter from scattering again
Space saving
Installation area: 41% reduction
Check valve enclosure
Flow order: Filter ➡ Check valve
Prevents foreign matter from getting caught in the check valve
Applicable tubing O.D.: ø4, ø6, ø8

Wireless System　EXW1/EX600-W Series

Updated Apr-25

Analog input, digital input/output, and valve manifold have been added to the compact type EXW1 series. [New]
Noise resistance
　Uses the 2.4 GHz ISM frequency band
　Frequency hopping: Every 2 ms (Fastest)
Communication cables not required
Reduced wiring work, space, and cost
Minimized disconnection risk
Provides communication stability in FA environments
Compact and lightweight (EXW1)
Volume: Approx. 81% reduction, Weight: Approx. 79% reduction

Non F-Gas (CO₂ Refrigerant) Refrigerated Thermo-chiller　HRZC Series

Updated Apr-25

Non F-Gas
Uses CO₂ refrigerant (R744)
Greatly reduced GWP
Air transport possible
Eliminates the need to pay for F-Gas recovery & disposal
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Solid State Auto Switch UL/CSA Certified　D-M9□-551/918

Updated Apr-25

D-M9□-551：UL, CSA certified
D-M9□-918：UL, CSA certified + Compatible with material restrictions for secondary battery manufacture
Dimensions and Specifications: The same as those of the standard (general purpose) D-M9□ auto switch

Angle Seat Valve / Air Operated Type　JSB Series

Updated Apr-25

High pressure type has been added. [New]
Low pressure loss due to angle seat structure!
Long service life: 10 million cycles (Air, Water), 3 million cycles (Steam)
Large flow rate
A large flow rate is possible due to the optimized flow channel shape. (Cv factor: approx. 2.5 times)
Compact: Height 166 mm (Port size: 1")
Abundant series variations of 7 sizes
All-in-One (Stainless steel 316L equivalent)
Air, Water, Steam

Stainless Steel Cylinder/Non-adjustable Air Cushion Type　HF2A-CG5 Series

Updated Apr-25

Equipment for the Food Manufacturing Industry
All stainless steel specifications (External parts: Stainless steel 304)
4 times better durability in environments where it may come into contact with water droplets
Non-adjustable air cushion
Mounting interchangeability between the stainless steel cylinder, CG5-S series

Polyethylene Tubing　TX/TIX Series

Updated Apr-25

Excellent chemical and heat resistance
Using materials compliant with Japan Food Sanitation Act, US FDA, and Regulation (EU) No. 10/2011^∗1
∗1 Using materials posted in the positive list
Operating temperature range
Air, Inert gas: −45 to 80°C
Water: 0 to 80°C (No freezing)

Fieldbus System (Serial Transmission System)　EX600 Series

Updated Apr-25

An IO-Link unit compatible terminal unit (IO-Link device) has been added. [New]
Supports digital inputs/outputs, analog inputs/outputs, and IO-Link units
Self-diagnosis function
Web server function
Various connectors available
Up to 9 units can be connected. (Excludes SI units)

[Compatible with Manifold Controller] Electric Actuators Slider Type/Rod Type/Guide Rod Type　LE2F□□H/LE2Y(G)□H

Updated Apr-25

Rotary Table Type LE2R□H Series has been added. [New]
Compatible with manifold controller
Up to 16 axes can be connected
Annual CO₂ emissions reduced by up to 38% through motor control optimization (SMC comparison)
8.7 kg-CO₂e/year (14.1)
∗ The numerical values vary depending on the operating conditions.
Battery-less absolute encoder type
Restart from the last stop position is possible.

Wireless Auto Switch　IN574 Series

Updated Apr-25

Wireless power supply and communication for a completely wireless system.
Cable free
Zero risk of problems due to wire disconnection
Zero cable space and wiring work required
Zero switch failure due to cable deterioration
Battery-less (Wireless power supply / Using WPT)
Zero maintenance for battery replacement
In Japan, a radio station license is required to use a power transmitter (WPT station).
An application fee for opening a station and a radio wave usage fee are required.
This product can only be used in countries that comply with Radio Law (Japan, United States, Canada).
This product cannot be used in non-compliant countries.

Wireless System/Compact Wireless Base　EXW1-X10

Updated Apr-25

Pairing with wireless remote and various parameter settings without using IO Configurator.
∗ Configuration of IO-Link devices not included.

Fieldbus System (Serial Transmission System) EX260 Series

Updated Apr-25

CC-Link IE TSN [New] , Safety over EtherCAT® [New] compatible
Space-saving installation
IO-Link compatible
IP67
Drives up to 32 solenoids
Daisy-chain wiring communication
RJ45 communication connectors (X205)

3-Port Solenoid Valve Modular Type/Residual Pressure Release Valve　VP346E/546E/746E/946E Series

Updated Apr-25

Can be connected to F.R.L. units (AC-D series)
Allows for space saving and reduced piping labor.
Flow rate characteristics C［dm³（/ s·bar）］
VP346E：4.2
VP546E：7.5
VP746E：12.6
Effective area mm²
VP946E：234
A model with a soft start-up function is also available.
Power consumption: 0.35 W (Without light)
Features a check valve built into the pilot flow path
(Supports pilot pressure drops caused by pressure fluctuations on the inlet side)

Air Management System　AMS30X/40X-X2044/X2045 Series

Updated Mar-25

IO-Link compatible
Monitoring compressed air condition via IO-Link and reduction of air consumption
Standby regulator＋Digital flow switch
[Suffix: -X2044]
Operation mode ⇔ Standby mode
Digital flow switch＋Residual pressure relief 3-port solenoid valve (With soft start-up function)
[Suffix: -X2045]
Operation mode ⇔ Isolation mode

Process Gas Equipment

Updated Mar-25

5 regulator/back pressure regulator models have been newly added.
19 diaphragm valve models have been newly added.

See Catalog

3-Screen Display High-Precision Digital Pressure Switch　ZSE20□(F)/ISE20□ Series

Updated Mar-25

A low differential pressure range type
has been added to the 20A series. [New]
An M12 connector type has been added.
A low pressure range type has been added.
Integrated R1/8 fitting with bottom wiring entry
Visualization of settings
Simple 3-step setting
Easy screen switching
It is possible to change the settings while checking the measured value.
Delay time:1.5 ms or less
IO-Link compatible

Air Saving Impact Blow Gun　IBG Series

Updated Mar-25

Various functions
Pulse function [New]
Adjuster function with indicator
Increased impact force due to higher peak pressure
Reduces air consumption and operation time
Application: It is capable of eliminating, in a short period of time, the dust, etc.,
that is difficult to remove with the existing blow gun.

Suction Cup　ZP3C Series

Updated Feb-25

Sizes ø20 and ø25 have been added for the 2.5-stage bellows type. [New]
Material: FS61 (Fluoro-based rubber) improves abrasion resistance
∗ More than 4 times the abrasion resistance of SMC's urethane suction cups
Reduced suction of foreign matter, such as paper particles, due to mesh filter
Can be replaced without tools
2.5-stage bellows type
Optional inner ring and retainer

Turn-lock Type All Resin Fitting　KY Series

Updated Feb-25

Prevents leakage due to insufficient tube insertion
Ensure secure tube insertion
Visibility of tube grip status is possible.
Grease-free
Fluid: Air, Nitrogen, Water, DI water (deionized water), Some chemicals
Operating temperature range: 0 to 80°C
All resin (Non-Metal) (except rubber)

Compact Position Sensor　D-MPG Series

Updated Feb-25

Detects the stroke position of compact actuators such as air grippers
Repeatability: 0.1 mm
Compact sensor head and separate teach unit
Same shape as the D-M9□ solid state auto switch
Analog output
Switch output
IO-Link compatible

ISO Standards (21287) Compact Cylinder　C55/CD55 Series

Updated Feb-25

Smooth cylinder (C55Y) has been added. [New]
Made of stainless steel (-XC6) has been added. [New]
With coil scraper (-XC35) has been added. [New]
Auto switch mounting groove: T-slot type (-X1439) has been added. [New]
Bore sizes ø12 and ø16 have been added. [New]
∗ These are not subject to ISO Standards (21287).
ISO Standards (21287)
1.8 times the anti-lateral load capacity
The allowable lateral load has been improved by changing the material of the bushing. (For ø20)
Increased the standard product's maximum stroke limit (to 300 mm)
Standardization of the double rod (C55W) type, smooth cylinder (C55Y), simple specials, and made-to-order options
Change of rod end shape (-XA□)
Heat-resistant cylinder (–10°C to 150°C) (-XB6)
Low-speed cylinder (5 to 50 mm/s) (-XB13)

Magnet Buffer　ZP3B□M Series

Updated Feb-25

A new nut material has been added. [New]
Stable buffer reaction force during stroke
Adsorbs workpieces with different heights, Reduces the impact applied to a workpiece
Low particle generation
No particle generation due to the friction of a spring (spring-less structure)
Non-rotating
Reduces rotation by 4-pole magnets
Copper and zinc-free
Compatible with secondary battery manufacturing processes

Pulse Valve Valve for Dust Collector　JSXF/JSXFA Series

Updated Jan-25

A bulkhead fitting has been added. [New]
A SMARTVENT type has been added.
The integrated control board eliminates the need for a control box.
Life: 10 million cycles or more/10 times or more
High peak pressure and low air consumption
Peak pressure: 15% increase, Air consumption: 35% reduction
Fluid temperature: −40 to 60°C
Can be used in a wide range of temperatures

3-Screen Display PSE Sensor Set Up Tool　PSE-ST Series

Updated Jan-25

Selectable from 2 models of IO-Link compatible compact pressure switch
Connection sensor detection
Automatic range detection and display!
Simple copy function
Automatic range detection and display!
Simple 3-Step Setting
Mobile Battery Connection
Connect via mobile battery for easy set up in any location!

Valve Manifold Integrated with Ejector System JSY1000-E Series

Updated Jan-25

Spacer type ejector with High-noise reduction silencer (Selectable) [New]
A vacuum release flow adjustment unit has been added. [New]
Compact All-in-One Manifold
The devices have been integrated into one for applications in which an actuator and vacuum suction are used together.
EtherCAT®，IO-Link [New] , PROFINET® [New] ，EtherNet/IP™ [New] compatible
Wiring/Piping Saving through Use of All-in-One Manifold
Installation area: 64%reduction
Weight: 42%reduction
Energy Saving Function
CO₂emissions (Air consumption) : 90% reduction

Refrigerated Thermo-chiller　HRSC Series

Updated Jan-25

Air transport possible
Uses CO₂ refrigerant (R744)
Greatly reduced GWP
Eliminates the need to pay for F-Gas recovery & disposal
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Rotary Actuators　CRB/CDRB Series

Updated Jan-25

A double vane type has been added for sizes 10 to 40. [New]
Features a compact body with a built-in angle adjustment unit and
auto switch unit (Size: 20, 30, 40)
Overall length: 44% shorter, Weight: 48% lighter
Piping, wiring, and angle adjustment can be performed on the same side for easier mounting.
Easy-to-adjust start and end positions with the angle adjustment bolts
(as standard)
The position of the chamfered portion of the shaft can be easily checked using the rotating angle indicator. (Only for the CDRB with auto switch)
Each of the units below for the CRB2 series can be mounted to the CRB series.

Tool Changer/Auto Type　RMTA Series

Updated Jan-25

Robot hand tool automatic exchange
Standards: ISO9409-1 compliant
Support for direct mounting on collaborative robots
Robot and end tool connection/release
More compact as flanges are not required.
Direct mounting on collaborative robots eliminates the need for flanges and reduces design labor
Supports a work load of up to 20 kg (Work load: 5 kg, 10 kg, 20 kg)

Tool Changer One-push Type/Clamp Type　RMTM Series

Updated Jan-25

2 types of manual tool changers
One-push Type
Tools can be attached/removed by the push of a button (no tools required).
Work load: 10 kg
Repeatability: ±0.01 (Position reproducibility)
Clamp Type
Tools can be attached/removed by clamper bolts (2 pcs).
Work load: 20 kg
Repeatability: ±0.02 (Position reproducibility)
Standards: ISO9409-1-50-4-M6 compliant
Compatible with the flanges of most major collaborative robots
Compact, Lightweight

Circulating Fluid Temperature Controller Thermo-chiller Dual Channel Refrigerated Thermo-chiller for Lasers　HRL Series

Updated Jan-25

A water-cooled refrigeration type has been added to the HRL100/200 series. [New]
Temperatures for 2 fluid channel systems can
be controlled individually by one chiller.
Space saving, Reduced wiring
Footprint: 22% reduction
One power supply system for 2 channels
Energy saving
Power consumption reduced by 30%
Touch panel

Stainless Steel Throttle Valve with One-touch Fittings In-line Type　HF2B-ASG-□TV Series

Updated Jan-25

Improved corrosion/heat resistance with the all stainless steel exterior
Possible for use in environments such as high temperature,
water splashing, and where copper and zinc cannot be used
Material: Stainless steel 316　∗ FKM (Seal)
Max. operating temperature: 150°C
NSF H1 grease
Fluid: Air, Water, N₂
Equipment for the Food Manufacturing Industry　HF2B- Series

Vacuum Gripper System (Foam Type)　ZGS Series

Updated Jan-25

Foam size: 300 mm x 180 mm / 200 mm x 120 mm [New]
Suitable for the palletizing and depalletizing of corrugated cardboard, etc.
Ejector unit
Combines all functions required for adsorption
(Ejector, Supply valve/Release valve, Silencer, Pressure switch)
Can be used immediately by simply connecting 1 electrical cable and air piping
Compatible with the collaborative robots of 4 companies
UNIVERSAL ROBOTS, OMRON/TECHMAN ROBOT, FANUC, YASKAWA Electric
Lifting force
440 N (200 x 120) (At −63 kPa)
880 N (300 x 180) (At −63 kPa)
2144 N (400 x 240) (At −75 kPa)
IO-Link compatible
∗ Only for sizes 300 x 180 and 200 x 120

[Low GWP Refrigerant Chiller] Thermo-chiller/Rack Mount Type　HRRF Series

Updated Jan-25

Low GWP refrigerant chiller
GWP: 146^∗　∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Operable without the need to remove the unit from the rack
Front access: Simple to control, service, and maintain with all filters and drainage accessible via the front panel
Space saving: Multiple chillers can be mounted to a 19-inch rack.
Cooling capacity: 1.2/1.8 kW (60 Hz)
Temperature stability: ±0.1°C
Power supply: Single-phase 200 to 230 VAC (50/60 Hz)

[Low GWP Refrigerant Chiller] Thermo-chiller/Standard Type　HRSF Series

Updated Dec-24

Low GWP refrigerant chiller
GWP: 146^∗
∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Lightweight/Compact　Same width for all models: 377 mm
Temperature stability: ±0.1°C
Compatible with power supplies in Europe, Asia, Oceania, and North, Central, and South America
Single-phase 200 to 230 VAC (50/60 Hz)

Water Separator for Vacuum　AMJ-D Series

Updated Dec-24

Removes water droplets in the vacuum line
Prevents vacuum equipment failures
Weight: Max. 30% reduction (AMJ40-D: 0.42 kg b AMJ4000: 0.6 kg)
Water drop removal ratio: 99% or more
Better environmental resistance with 2-layer construction
The bowl is covered with a transparent bowl guard.
Superior visibility: 360°

Pin Clamp Cylinder Lateral Compact Type　C(L)KQ32-X3445

Updated Dec-24

Lateral Compact Type
Compact: Overall length: 94 mm shorter (183mm→89mm)^∗
Lightweight: Weight: 38% reduction (900g→560g)^∗
∗Compared with the existing product CKQG32-X2081, LOW type, without lock
Lock mechanism to prevent the dropping of workpieces during emergency stops
Various clamp arm positions and port positions are available.
Mountable on 2 surfaces

High Speed/High Frequency Cylinder　CM2/CQ2-X3423

Updated Dec-24

Maximum piston speed: 2500mm/s
Maximum operating frequency: 15Hz
Kinetic energy: 1.5 times (Compared with the standard product)
Reduced impact due to revision of cushion structure
Reduced weight of moving parts (piston rod, piston, etc.)

Resin Pilot Operated 2-Port Solenoid Valve　JSXN-X1

Updated Dec-24

Body material: High strength PA66
Piping type
・Socket
・Thread: Rc, NPT, G
Fluid*　*Fluids that will not corrode wetted parts
・Water
・Diluted pesticides
・Liquid fertilizer
A water hammer relief feature
Seal material: NBR, FKM, EPDM
Power consumption: 3 W

Magnet Gripper/3-Position Type ø32　MHM-X7776

Updated Dec-24

Allows for high-speed transfer
Prevents the accidental attraction of a second workpiece and allows for high-speed transfer.
Improved cycle time
Gripper mountable on 3 surfaces (Excludes the port side)
Stopper (scale) allows for holding force adjustment and improved visibility

[Low GWP Refrigerant Chiller] Thermo-chiller/Dual Channel Thermo-chiller for Lasers　HRLF Series

Updated Dec-24

Low GWP refrigerant chiller
GWP: 146^∗
∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant
(Not available for air transport)
Temperatures for 2 fluid channel systems can be controlled individually by one chiller.
Space saving, Reduced wiring
Touch panel
Numeric keypad inputs
Notice for alarms and maintenance
Temperature waveform can be displayed.

Lever Hand Valve　VHL Series

Updated Nov-24

Space saving, Easy to operate (Vertical type) 5-port lever valve
Weight reduction of up to 45%
∗ Comparison between VHL21□D-02□ and VH210-□02
Footprint reduced by 58%
VHL210D 3216.5 mm² ⬅ VH20□ 7750 mm²
Panel mounting internal height reduced by 18.6 mm
For panel mounting
∗ Comparison between VHL210D and the existing VH20□ model
Flow rate increased by 73%
∗ Comparison between VH211□-02□ and VH210-□02
(Flow rate characteristics 1 → 4/2 (P → A/B))
3 operation types

Suction Cup/With Non-slip Feature　ZP3M Series

New

Updated Jun-25

An oval bellows shape with non-slip feature has been added. [New]
Longer life (More than twice that of urethane cups)
Cup material: FS61 (Fluoro-based rubber) with excellent abrasion resistance
Reduced number of cup replacements
Non-slip special ribs
Diagonal ribs are radially arranged to secure the gripping force in all directions.
・Prevents workpiece slippage
・Secure adsorbing and transferring are possible.
Bowl shape with excellent flexibility
Curved workpieces can also be adsorbed.
The cup follows the workpiece shape, making stable adsorption possible.
Horizontal holding force: 387 N (Cup diameter ø100)
Suitable for high-temperature workpieces (200°C)
Suitable for workpieces with oil film
As oil is ejected to the grooves between special ribs, the lateral slipping of workpiece can be suppressed even on a steel plate with oil film.

IO-Link Compatible 2 in 1 Auto Switch　D-MH2□ Series

Updated Nov-24

Outputs process data according to the actuator stroke position
A single switch can discriminate between max. 3 position points.
Discriminable resolution: ±0.1 mm　∗ Within the high-resolution range
Detection position setting can be done away from the actuator.
Process data output (–1000 to 1000)
Can also be used with the 2 in 1 auto switch single unit if there is an IO-Link master

Low Profile Air Gripper　MHF2 Series

Updated Nov-24

ø25 and ø32 have been added. [New]
High rigidity, Gripping point distance: Max. 170 mm (For ø32, at 0.4 MPa)
Height: Max. 66% reducti
Moment reduction when transferring workpieces
72.8 mm → 25 mm(Comparison with our MHZ2 Series equivalent gripping force products)
3 types of strokes available for each size
Short stroke, Medium stroke, Long stroke

Vacuum Manifold for Fieldbus System　ZKJ Series

Updated Nov-24

Vacuum pads and actuator driving can be
controlled with a single manifold [New]
Positive pressure unit
5-port solenoid valve [New]
Vacuum unit
Energy saving ejector Air consumption: 92% reduction
Fieldbus compatible
Space saving: Requires no separate input/output units
Reduced wiring time
Compatible protocols: PROFINET, IO-Link, EtherNet/IP, EtherCAT
Exhaust sealing function
Quick workpiece release
4 stations/8 stations/12 stations/16 stations manifold compatible

Ionizer / Bar Type　IZS51 Series

Updated Nov-24

High speed static neutralization: Fastest time 0.1 s
Space saving: Height 70 mm x Width 28 mm
Compact and flat body
Can be mounted in narrow spaces
Supports the IO-Link communication protocol
Low maintenance cartridge
Concentrating the air (for reducing emitter contamination)
around the emitter and the assisting air (for ion transfer)
Reduces dirt on the emitter, compared with the existing model
Valve unit option
For reduction in air consumption by stopping air purge during stand-by mode

e-Actuator Easy to Operate Integrated Controller　Slider Type/Rod Type/Guide Rod Type　EQFS□H/EQY□H/EQYG□H Series

Updated Oct-24

Guide Rod Type　EQYG□H Series [New]
Size: 16, 25, 32
Communication cable with Push-Pull connector
Easy to set up, just like air equipment!
Two position stop with no programming required
Three position stop with no programming required
Cycle time can be set in all control modes.
Downsized with Integrated Controller, Wiring saving, Labor saving
· Programless · Reduced adjustment time
Annual CO₂emissions reduced by up to 59% through motor control optimization [5.8 kg-CO₂e/year (14.1)]
∗ The numerical values vary depending on the operating conditions.

Clamp-on Type Flow Sensor IP65　PFUW Series

Updated Oct-24

Benefit from the eight “zeros” with clamp mounting!
Zero piping work
Zero leakage
Zero clogging
Zero pressure loss
Zero fluid contact
Zero fluid contact parts material concerns
Zero foreign matter entry into piping
Rated flow rate range from zero L/min
“Easy mounting and retrofitting” Reduced installation work

Air Cylinder ø20, ø25, ø32, ø40　CM2 Series

Updated Oct-24

A double rod type, a single acting type, a non-rotating rod type, and a direct mount type have been added. [New]
Made-to-order options have been added. [New]
Special port location (-XC3), Made of stainless steel (-XC6), Dust resistant cylinder (-XC4), Heat- resistant cylinder (-XB6), etc.
Cylinder with rod end bracket is standardized.
Interchangeable in mounting with the existing model
Various mounting bracket options
Mounting brackets suitable for various installation conditions
Improved mounting flexibility
Part numbers for products with a rod end bracket and/or a pivot bracket available

4-Position Dual 3-Port Valve: Body Ported/Base Mounted　SY5000/7000-X701

Updated Oct-24

Features two 3-port valves built into one body
The dimensions are the same as those of the double solenoid.
The 3-port valves on the A and B sides can be operated independently.
When used as a 3-port valve, only half the number of stations are required.
Mixed mounting on the standard SY5000/7000 series 5-port solenoid valve manifold base is possible.

Non F-Gas (CO₂ Refrigerant) Refrigerated Thermo-chiller　HRZC Series

Updated Apr-25

Non F-Gas
Uses CO₂ refrigerant (R744)
Greatly reduced GWP
Air transport possible
Eliminates the need to pay for F-Gas recovery & disposal
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)

Low GWP Refrigerant Chiller Thermo-chiller Standard Type　HRSF150/200 Series

Updated Sep-24

Low GWP Refrigerant Chiller
GWP: 146^∗　∗Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant (Not available for air transport)
No heater is required, as the circulating fluid is heated using only the heat exhausted by the refrigerating circuit.
Compatible with power supplies in Europe, Asia, Oceania, and North, Central, and South America
3-phase 400 VAC
Low-noise design 70 dB(A)
Outdoor installation IPX4

[Model with Residual Pressure Release Function] Compact Indicator Type Speed Controller with Pilot Check Valve　ASP-S Series

Updated Sep-24

Flow rate control is possible via the compact indicator.
Model with residual pressure release function: Cylinder pressure can be manually released.
Model without residual pressure release function: Temporary intermediate stops are possible.
Horizontal and vertical types are available, which can be selected depending on the installation conditions.
Easily mounted using a hexagon wrench

3-Screen Display Condensation Checker (Digital Temperature & Humidity Switch)　PSH Series

Updated Sep-24

A relative humidity under pressure (inside piping) display function has been added. [New]
A condensation checker can prevent such problems!
Allows for the visualization of humidity inside piping
Detects abnormalities prior to condensation generation
Can be easily connected to any pipe you want to monitor
Compact size allows for easy installation
Visualization of relative humidity
Real-time monitoring
Remote/Condition monitoring
Remote confirmation via switch output preventing condensation problems!

Suction Cup/Compatible with Metal Detectors　HF3A-ZP3F Series

Updated Sep-24

Bellows type cup with excellent cushioning and flexibility
Reduces the deformation of soft workpieces such as bread
The cups and retainers are made of materials compliant with the FDA (U.S. Food and Drug Administration)
dissolution test, EC directives, and Japan Food Sanitation Act standards.
Improved durability due to anti-stick grooves
Equipment for the food manufacturing industry HF3A- series

Pilot Operated 2-Port Solenoid Valve　JSXH-X1

Updated Sep-24

Max. operating pressure differential: 4.0 MPa
Application examples: Blow molding, Laser processing machines, Nitrogen filling unit
Fluid: Compressed air, Nitrogen, Argon, Oxygen^∗
∗ When using oxygen, please refer to "Fluid Supply."
Improved environmental resistance
Dustproof/waterproof IP67 structure (IP65 for the DIN terminal)
With a stainless steel coil cover
Low particle generation
Oil-free
Easy maintenance
The coil can be replaced by simply removing the clip.
Power saving (Power consumption: 6 W)

Compact Guide Cylinder ø12, ø16, ø20, ø25, ø32, ø40, ø50　MGPK Series

Updated Aug-24

A type with an air cushion has been added for
bore sizes ø12 to ø50. [New]
Symmetrical port positioning has been standardized. [New]
Volume: Max. 28% reduction（538cm³ → 390cm³）
Weight: Max. 41% reduction (0.32 kg → 0.19 kg)
High rigidity: Optimized configuration allows for compact body with high rigidity
Plate thickness increased by up to 33%, Higher rigidity
Lube-retainer is added to the guide rod.

Standard Air Cylinder (Square Cover)　MB2/MDB2 Series

Updated Aug-24

3 times better durability due to the air cushion + rubber bumper structure
Allowable kinetic energy: Max. 1.5 times
Has the same kinetic energy as the existing MB series product which is 1 size larger
CO₂ emissions (Air consumption) can be reduced by up to 39%.
CO₂ emissions (Air consumption) can be reduced due to downsizing. (Air consumption for one cycle)
The overall length, mounting dimensions, and mounting brackets are interchangeable with the existing MB series product.

Compact 5-Port Solenoid Valve A top-ported type　JSY3000 Series

Updated Jul-24

A top-ported type has been added to the JSY3000 series.
4(A) and 2(B) port output pressure detection is possible.
(Caution) The mounting bases are side ported.

Longer Life Cylinder　C55-XB24

Updated Jul-24

New technology offers at least 4 times better durability.
The maintenance intervals will be extended.
Employs the same specifications and dimensions as the existing model,
C55 ISO Cylinder series.
ISO Standards (21287)

Energy Saving, Exhaust-Recovery Booster Regulator　VBAE Series

Updated Jul-24

CO₂ emissions (Air consumption) :Max. 40% reduction
(Based on SMC's measuring conditions)
Driven by reusing the exhaust air
Increase factory air pressure by 1.7 times Air-only operation that requires no power supply, and allows for easy installation.
Operation noise: 65 dB (A)
15 dB (A) reduction compared with the existing model (VBA series) (Based on SMC's measuring conditions)
Charging time: Max. 50% shorter
Reduced maintenance frequency due to improved life
(Based on SMC's measuring conditions)
Compatible with vertical and horizontal installation
Mounting interchangeability with the existing model (VBA series)

2-Color Display
Digital Flow Switch　PF2M7(-L) Series

Updated Jul-24

3-Screen Display Digital Flow Monitor (Dedicated for the PF2M7) [New]
Allows for the monitoring of remote lines PFGM302 Series
Dry air, N₂, Ar, CO2
A wide range of flow measurement is possible with 1 product.
Flow ratio 100:1, Smallest settable increment: 0.01 L/min
Improved resistance to moisture and foreign matter
Compact, Lightweight
Weight: 27.3% lighter (55g ⇒ 40g)
Low current consumption: 35 mA or less
Grease-free
IO-Link compatible

Biomass Tubing　TU/TS/T-X309

Updated Jul-24

Tubing according to carbon neutrality
CO₂ reduction amount: Max. 18.7 kg
∗ Comparison with the TS series (Tubing O.D. 12 mm; Tubing I.D. 9 mm), Soft nylon tubing, 100 meters roll
Reduction in CO₂ and greenhouse gases by reducing the use of petroleum driven raw materials, resulting in a greater contribution towards decarbonization.

High Purity Air Operated Chemical Liquid Valve　JLV20/30/40/50 Series

Updated Jun-24

Body class 4 has been added.[New]
Suppresses the generation of particles and reduced footprint!
The special structure allows for reduced impact when the valve is closed
as well as particle generation suppression.
Reduced footprint (Compared to the existing model):
Valve width reduced by 20%, Mounting pitch reduced by 45%
Applicable for applications requiring high pressure/high back pressure
Operating pressure: 0 to 0.5 MPa, Back pressure: 0 to 0.5 MPa
　(Improved by 66% compared to the existing model)

Electric Stopper Cylinder　LEB□ Series

Updated Jun-24

Designed in response to customers' requests for a motorized conveyor line
With 2 control types available depending on the application
Controller
Controllerless
Ensured stopper cylinder mounting interchangeability with equivalent stopper performance
Easy replacement of shock absorbers Replaceable just by loosening the set screw

Electric Actuator/Rod Type Dust-tight/Water-jet-proof (IP69K Equivalent) 　HF2A-LEY Series

Updated Jun-24

Enclosure: IP69K equivalent
Smooth design for less residual liquid accumulation
External parts: Stainless steel 304
Scraper, Static seal: US FDA compliant material (Blue), EC1935/2004 compliant material
Grease: NSF-H1 grade
Equipment for the Food Manufacturing Industry　HF2A- Series
Lubricants or rust proof agents are not used for the external parts.
Otherwise, lubricants or rust proof agents for the food machinery are being used.
US FDA compliant materials are used.
Work load: Max. 80 kg^∗ 　∗ Size 63, Lead C
Stroke：Max. 800 mm^∗ 　∗ Size 63

IP69K is the degree of protection against dust and hightemperature/high-pressure water washdown specified in DIN 40050-9 and currently specified in ISO 20653 and JIS D 5020.

Separate Controller Ionizer / Slim Bar Type　IZT44/45 Series

Updated Jun-24

Powerfully eliminates static electricity from highly charged workpieces
Pulse AC type, High density emitter arrangement (6 times the number of emitters^∗)
∗ Compared to the existing model
Can be mounted in a narrow space (Height 23 mm x Width 20 mm)
Can be installed through gaps between equipment
Improved installation, replacement, and maintenance in narrow spaces
Powerful static elimination is possible without air supply.
High speed static elimination: Discharge time reduced by approx. 60%
2-way directional static elimination using branch cables
2 ionizer bars can be connected to one high voltage power supply.
Up to 4 high voltage power supply modules can be connected to one controller. (IZT45)
Flexible layout possible with various module connection methods (IZT45)
Controller to Bar maximum installation distance: 15 m

Electro-pneumatic Regulator Integrated Type 64-station Compatible Manifold Plug-in Compact 5-Port Solenoid Valve　JSY3000-P Series

Updated Jun-24

Solenoid valves and electro-pneumatic regulators can be connected to the same manifold.
Valve stations/Number of outputs: For 4 to 64 stations^∗ /128 points
∗ Stations are only available in multiples of 4.
Electro-pneumatic regulator stations: 1 to 4 stations
I/O unit stations: Max. 8 stations
Equipment integration allows for the centralized management of control and wiring as well as reduced wiring
Reduced wiring, Reduced number of SI units, Reduced wiring work, Compact

64-station Compatible Manifold Plug-in Compact 5-Port Solenoid Valve　JSY3000-L Series

Updated Jun-24

Valve stations/Number of outputs: For 4 to 64 stations^∗ /128 points
∗ Stations are only available in multiples of 4.
Space saving, Reduced number of SI units, Reduced wiring and wiring work

Speed Controller with Compact Indicator　AS-FSA Series

Updated May-24

Height: Max. 5.4 mm shorter
Flow rate can be controlled numerically with the indicator window.
Due to the vernier indication, it is possible to configure fine settings in 1/4 increments.
Reduces work-hours and setting mistakes
A type with a panel mount adapter has been added. [New]
No tools required, Reduced installation work

In-line Type AS Series

Updated May-24

A panel mount type has been added. [New]
No tools required, Reduced installation work
Reduces labor time
Easy to use push-lock type
Knob O.D.: Almost doubled
Improved reproducibility of flow rate
Lightweight: Weight reduced by approx. 27%
Electroless nickel plated type is standard.

Electric Actuator/Slider Type (Improved Dust and Water-jet Resistance)　LEFSW Series

Updated May-24

A dust-tight and water-jet-resistant (IP65 equivalent) slider type product
Newly developed special wear-resistant seal band
A special wear-resistant seal band is mounted on the bottom to prevent dust and water from entering the inside of the product.
With internal battery-less absolute encoder
Restart from the last stop position is possible after recovery of the power supply.
Reduced maintenance (No need to manage or replace batteries)
Work load：Max. 65 kg (Size 40, Lead B)
Stroke：Max. 1200 mm (Size 40)

Low GWP Refrigerant Chiller/Refrigerated Thermo-chiller　HRZF Series

Updated May-24

Low GWP refrigerant chiller
GWP: 146^∗　∗ Regulation (EU) 2024/573, AIM Act 40 CFR Part 84
EU refrigerant regulations: GWP150 or more
US refrigerant regulations: GWP700 or more
California, US refrigerant regulations: GWP750 or more
Environmentally friendly R454C as refrigerant (Not available for air transport)
More effective energy-saving is achieved through use of a DC inverter compressor and an inverter pump.

Compact Slide ø6, ø10, ø16, ø20, ø25　MXH2 Series

Updated Apr-24

Size ø25 have been added. [New]
Same width as size ø20
Allowable moment: Max. 1.4 times greater than that of size ø20
Improved linear guide rigidity reduces the amount of table displacement by 48%
Displacement due to a force acting in the pitch direction: 48% reduction (0.31 mm→0.16 mm)
Displacement due to a force acting in the yaw direction: 63% reduction (0.24 mm→0.09 mm)
Displacement due to a force acting in the roll direction: 90% reduction (0.06 mm→0.006 mm)
Max. standard stroke: 150 mm (For ø20, ø25)[New]
Weight: Max. 6% reduction (194 g→182 g)
Dimensions for mounting and length are equivalent to the existing MXH series.

Stainless Steel Speed Controller (Max. operating temperature: 150°C) In-line Type　ASG Series

Updated Apr-24

Improved corrosion/heat resistance with the all stainless steel exterior
Possible for use in environments such as high temperature, water splashing, and where copper and zinc cannot be used
Material: Stainless steel 316 (External metal parts)^∗, FKM (Seal)
∗ Stainless steel 304 is used as the material for parts other than body A.
Max. operating temperature: 150°C
NSF H1 grease

Pulse Blow Valve　AXTS040-X202

Updated Apr-24

The peak pressure of repeatedly colliding air permits efficient blowing.
CO₂ emissions (Air consumption) : 50% reduction
Control for pulse generation is not required.
Pulse blow can be used by simply supplying air.
Built-in pilot valve construction allows for stable blowing.

Air Management System　AMS20/30/40/60 Series

Updated Apr-24

Air consumption: Max. 62% reduction
Monitors the machine standby conditions (when production stops) and automatically decreases the pressure.
Reduces unnecessary air consumption
Compatible with OPC UA
Direct connection enables data communications.
Compatible with wireless systems
Communication cables not required
High security thanks to unique encryption
Communication distance: Max. 100 m
IO-Link compatible

Low-Pressure / High-Precision Type 5.0 MPa Maximum Supply Pressure High Pressure Electro-Pneumatic Regulator　ITVX2030-X10

Updated Mar-24

Improved accuracy at 1 MPa or less
Repeatability: Repeatability
Pressure stability: 0.5% F.S. or less
Max. supply pressure: 5.0 MPa
Set pressure range: 0.01 to 3.0 MPa
Max. flow rate: 3000 L/min (ANR)
Fluid: Air, N₂, O₂, Ar
Wetted parts: Fluorine grease

Compact Cylinder/High Power Type　CQE Series

Updated Mar-24

Sizes 25 and 40 have been added. [New]
Theoretical output: 1.5 times
This is done even with the same external dimensions of the CQ2 series.
The theoretical output of the next larger bore sized cylinder is made possible with the polygonal piston shape.
Contributes to a lower pressure air line
Supply pressure decreaed by 0.17 MPa
The same theoretical output is available even when the supply pressure to the cylinder is decreased.

Compact Cylinder 　CQ2/CDQ2 Series

Updated Mar-24

Sizes ø4, ø6, and ø10 have been added. [New]
ø4 to ø200 lineup
Space-saving cylinder designed with a compact body
Small auto switches can be mounted on 4 surfaces. (1 surface for ø6 annd ø10, 2 surfaces for ø12 to ø25)
No projection of the auto switch
Weight: Reduced by 5 to 13% (Compared with the existing CQ2 series)
Newly added compact type foot brackets and double clevis pivot bracket
Part numbers with a rod end bracket and/or mounting bolt are available. (It is not necessary to order a bracket for the applicable cylinder separately.)
With auto switch (CDQ2 series: CDQ2, CDQ2W, CDQ2K, CDQ2KW, CDQP2, CDQ2□S, CDBQ2)

Manifold Controller　JXD1-M□ Series

Updated Mar-24

Up to 16 axes can be connected
Max. 8 driver units can be connected
Fanless design (no cooling fan)
No cooling fan = No need to worry about fan replacement
Operating temperature range: 0 to 55°C
Communication protocol
CC-Link
EtherNet/IP™
EtherCAT^®
PROFINET^®
Cables, etc. can be attached from the front.

Direct Operated/Pilot Operated 2-Port Solenoid Valve　JSX/JSX□ Series

Updated Mar-24

A pilot operated steam type (JSXP series) has been added. [New]
Improved environmental resistance due to the stainless steel coil cover【IP67 enclosure/NEMA4X^∗】
∗ IP65 for models with a DIN terminal
Space saving
Compact: Valve volume reduced by 25%^∗, Lightweight: Weight reduced by 30%^∗
∗ Compared with the existing model
Energy saving
Coil force: 10% increase^∗, Power consumption: 14% reduction^∗
∗ Compared with the existing model
360° lead wire insertion and removal is possible.
Improved weather resistance in outdoor environments

Multi Hand Adapter　RMMA Series

Updated Mar-24

Allows for the handling of various workpieces by a single robot
Allows for the simultaneous transfer of multiple workpieces
Up to 3 grippers can be mounted.
Reduces tool changing time
Robot arm end standards: Equivalent to ISO9409-1-50-4-M6
3 gripper mounting angles

Air Flow Controller　IN502-44/45/46

Updated Mar-24

A rated control flow rate range of 200 to 2000 L/min has been added. [New]
Automatic flow rate adjustment is possible.
Dry air, N₂
Control accuracy: ±5% F.S.
Responsiveness: 0.5 s or less
Space saving/Reduced piping, wiring, and installation labor
Various types of grease can be selected.
Grease compatible with low dew points, White vaseline, Grease for food
IO-Link compatible

Modular Type Water Separator　AFG-D Series

Updated Mar-24

The no filter element design achieves a large flow and maintenance free construction.
Water droplets are removed by centrifugal force.(Water droplet removal ratio: 99%)
Air containing water droplets is rotated to remove them by centrifugal force.
Modular Design with Uniform Body Style

2-Layer Fluoropolymer Polyurethane Tubing　TUE Series

Updated Mar-24

2-layer tube with excellent environmental resistance and flexibility
Outer layer: Fluoropolymer, Inner layer: Polyurethane
Tubing I.D.: Cross-section ratio increased by 44% (Compared to TU0805)
Wide color variations
Available in black, white, blue, and translucent colors.

Longer Life Cylinder　C85/C75-XB24

Updated Mar-24

New technology offers at least 4 times better durability.
The maintenance intervals will be extended.
Employs the same specification and imensions as the existing models,
C85 ISO Cylinder series and C75 Air Cylinder series.

Multistage Ejector　ZL1/ZL3/ZL6 Series

Updated Mar-24

An IO-Link compatible vacuum pressure switch has been added. (ZL3, ZL6) [New]
Allows for ejector control with a single communication line
Reading of the device information and parameter batch settings are possible.
Max. suction flow rate: 3 types available: 100, 300, and 600 L/min (ANR)
Air consumption: 91% reduction (ZL3, ZL6)
Reduced by the pressure switch for vacuum with energy saving function and efficient ejectors
Weight: Max. 60% reduction [ZL112 (Existing model): 450 g → ZL1: 180 g]

Remote Type Pressure Sensors/Pressure Sensor Controllers　PSE Series

Updated Feb-24

Switch output specification [New]
IO-Link compatible [New]

Elastic Finger　MH-X7654

Updated Feb-24

Rubber sheet fingers enable gripping of an indefinite workpiece
Design of the finger according to the workpiece shape is not required.
Allows for gripping of tightly packed workpieces
The elastic finger mounting attachment to be produced by the customer.
Material
　・Silicone rubber (Blue)
　　This product is made of materials compliant with FDA
　　 (U.S. Food and Drug Administration) regulations
　　as well as Japan Food Sanitation Act standards.
　・EPDM (Black)

Electric Vacuum Gripper for Collaborative Robots　ZXPE5 Series

Updated Feb-24

Can be used with the collaborative robots of 4 companies
UNIVERSAL ROBOTS
OMRON/TECHMAN ROBOT [New]
FANUC CORPORATION [New]
YASKAWA Electric Corporation [New]
A vacuum gripper that doesn't require an air source
Operation possible by simply connecting an electrical wire connector
Can be used without an air source due to the built-in vacuum pump
Unitization of the peripheral devices required for adsorption
The vacuum pump, atmospheric release valve, pressure monitor, and cups have been integrated.
Current consumption: Max. 64% reduction
Energy-saving operation possible via automatic/manual modes
Lightweight: 556 g
A wide variety of cup variations are available to support a wide range of workpiece shapes.
Standards: Conforming to ISO9409-1-50-4-M6

Thermo-chillers for the Semiconductor Industry　INR-495-042/INR-495-043

Updated Feb-24

Non F-Gas (CO₂ refrigerant R744)
GWP: 1 (Natural refrigerant)
EU refrigerant regulations: GWP150 or less^∗
US refrigerant regulations: GWP700 or less^∗
California, US refrigerant regulations: GWP750 or less
∗As of December 2023
Air transport possible
No air transport restrictions for non-toxic and non-flammable^∗ refrigerants
∗A1 (ASHRAE34 standard)
No F-Gas management required
Eliminates the need for periodic inspections based on the Fluorocarbon Emissions Control Act (Japan)
No F-Gas recovery & disposal costs

Metal Speed Controller/Low Profile Type　ASBL Series

Updated Feb-24

Improved environmental resistance with the all metal exterior
For use in environments with welding spatter, dust, ultraviolet, etc.
Improved installability using a hexagon wrench
Improved piping design flexibility (360° rotation)
Reduced height when installed: Approx. 30% reduction
(when a knob is fully opened)
∗ 21.2 mm: ASBL23□1-01-06 ◀ 30.9 mm: ASB22□1-01-06

Motorless Type　LE□ Series

Updated Feb-24

A large slider type (LET-X11 series) has been added. [New]
A high precision type slide table (LESYH series) has been added. [New]
Your motor and driver can be used together
Manufacturers of compatible motors: 18 companies

Analog Auto Switch and Display Sensor Monitor　D-MH1□ Series

Updated Feb-24

Outputs the analog voltage according to the actuator stroke position
A single switch can discriminate between max. 3 position points.
Repeatability: ±20 mV (Converted stroke ±0.1 mm)
Discriminable dimensional difference: 0.2 mm
∗ The value is in the high-resolution range. The converted stroke value varies depending on the actuator.
∗ For air grippers, this is the value for one side of the finger. When it is converted to the dimension of the workpiece to be gripped, the value is doubled.
Detection position display and setting away from the actuator are possible.
Analog voltage output (1 to 5 V)
　Can also be used with the analog auto switch single unit
Reduced setting labor
　No need to fine-tune the switch mounting position
　Easy adjustment even in narrow places and on moving parts
Improved productivity
・Gripper fully open R gripping R gripping failure detection
・Minimized lead wire disconnection risk
Preventive maintenance
・Display of gripper finger wear
・Visualization of daily inspections (Origin position/ Gripping position)

Vacuum Unit Ejector System/Vacuum Pump System　ZK2□A Series

Updated Jan-24

Supply valve: An N.O. specification has been added. [New]
Can hold vacuum^∗ even when the power goes out or is turned off
Prevents the sudden dropping of workpieces^∗
∗ Supposing the supply pressure is being maintained
An IO-Link compatible pressure switch has been added. [New]
Allows for ejector control with a single communication line
Reading of the device information and parameter batch settings are possible.
Compatible with ejector systems and vacuum pump systems
Energy saving ejector
Air supply is cut-off when vacuum is reached.
Air consumption: 93% reduction (Under SMC’s measurement conditions)
More efficient ejector: Suction flow increased by 50%
(Compared to other SMC 1-stage ejectors)
Energy saving efficiency: 93% reduction
Improved low noise and suction flow by adoption of a high-noise reduction silencer

Electric Gripper for Collaborative Robots　LEHR Series

Updated Jan-24

Can be used with the collaborative robots of UNIVERSAL ROBOTS, FANUC CORPORATION, and OMRON/TECHMAN ROBOT
2 variations are available.
Gripping force: 60 to 140 N
Operate by simply connecting 1 electrical wire
Annual CO₂ emissions reduced by up to 52% through motor control optimization (SMC comparison)
With internal battery-less absolute encoder
Easy tool changing (Manual changer)
Compatible plug-in software: URCap

Wear Resistant Tubing/Clear Type　TUZC Series

Updated Jan-24

Abrasion: Approx. 1/3
(Compared with SMC polyurethane tubing TU series)
Clear type
Transparency in which the inside contents of a tube can be seen.

Flow Controller for Air PFCA7 Series

Updated Jan-24

For the automatic adjustment of the flow rate
Applicable fluid: Dry air, N₂, Ar, CO₂
Color display/2-screen display supported
For the confirmation of the instantaneous flow rate, flow rate command value, and accumulated flow rate at a glance
IO-Link compatible
Flow ratio 100:1